HomeMy WebLinkAbout2015 Sewer Vacuum Truck- Titan Machinery, Invitation to Bid CITY OF BOZEMAN, MONTANA
INVITATION TO BID
NOTICE IS HEREBY GIVEN that the City of Bozeman, Montana, is accepting sealed bids for
the:
CITY OF BOZEMAN SEWER VACUUM TRUCK
Sealed bids for the City of Bozeman's Sewer Vacuum Truck Purchase will be received by the
City Clerk, City Hall, 121 N. Rouse Avenue, P.O. Box 1230, Bozeman, Montana 59771-1230
until 2:00 p.m. mountain standard time,July 1,2014 and then publicly opened and read aloud.
Please write the name of the nroiect: Sewer Vacuum Truck
on the front of the sealed bid.
The nhysical address is:
City Clerk's Office, Suite 202, City Hall, 121 N. Rouse Avenue, Bozeman, Montana.
The mailine address is:
City Clerk's Office, Suite 202, City Hall, P.O. Box 1230, Bozeman, Montana, 59771.
Bids must be received before 2:00 p.m. Tuesday, July 1, 2014. Original copies must be
submitted—no faxed of electronic bids will be accepted. Bids will be opened and read following
the close of bids.
The purchase is detailed in the Instructions to Bidders, Bid Specifications, Bid Form, and
Purchase Agreement.
Further requirements for this project including the Instructions to Bidders, Bid Specifications,
Bid Form, and Purchase Agreement may be obtained at the office of the City Clerk, City Hall,
121 North Rouse, Suite 102, Bozeman, Montana 59771, telephone number (406) 582-2320, by
e-mail at agenda@bozeman.net, or interest parties may down the project requirements at
www.bozeman.net under the "Business"tab, and the RFP/BID drop down menu.
As required by the Instructions to Bidders, any entity submitting a bid under this invitation must
sign and return the required affirmation stating that they will not discriminate on the basis of
race, color, religion, creed, sex, age, marital status, national origin, or because of actual or
perceived sexual orientation, gender identity or disability in the performance of the work under
this invitation should it be awarded to that entity. Each entity submitting under this invitation
shall also recognize in writing the eventual contract will contain a provision prohibiting
discrimination as described above and this prohibition on discrimination shall apply to the hiring
and treatment of the Contractor's employees and to all subcontracts.
Also as required by the Instructions to Bidders, each bid or proposal must be accompanied by a
Certified Check, Cashier's Check, or Bid Bond payable to the City of Bozeman, Montana, in an
amount not less than ten percent(10%)of the total amount of the bid.
No bid may be withdrawn after the scheduled time for the public opening of bids, which is 2:00
p.m. local time,July 1,2014.
The City reserves the right to reject any or all bids received, to waive informalities, to postpone
the award for a period of not to exceed Sixty (60) days, and to accept the bid which is in the best
interests of the City.
Dated at Bozeman, Montana, this 10h day of June, 2014
Stacy Ulmen, CMC
City Clerk, City of Bozeman
Published Bozeman, Montana
Sunday,June 15`h, 2014
Sunday, June 22"d, 2014
INSTRUCTIONS TO BIDDERS (City of Bozeman Sewer Vacuum Truck Purchase)
BID DOCUMENTS: The bid documents for the City of Bozeman Sewer Vacuum Truck Purchase
include the Invitation to Bid, this Instruction to Bidders, the Bid Specifications, the Bid Form, and the
Purchase Agreement.
BIDS: All bids must be legibly written in ink. No alterations by erasures or interlineations will be
permitted in bids or in the printed forms. Each bid shall be enclosed in a sealed envelope addressed to:
Bozeman City Clerk, PO Box 4230 Bozeman, Montana 59771, or physically delivered to the address on
the Invitation to Bid and endorsed on the outside of the envelope with the words: Sewer Vacuum Truck
Purchase.
Bids shall be strictly in accordance with the prescribed Bid Form. Any modifications thereof or
deviations there from may be considered as sufficient cause for rejection. Bids carrying riders or
qualifications to the bid being submitted may be rejected as irregular.
Each Bidder must return a signed Bid Form incorporating as Exhibit 2 a copy of the Bid
Specifications indicating on each line item of equipment or required service whether the Bidder can
provide the equipment/service shown in that category or whether the Bidder can provide similar
equipment or required service meeting the listed equipment or required service and indicating the
details of the alternative equipment or required service. The City reserves the right to reject any
alternative equipment or required service.
Each bid shall indicate the total bid price.
The price quoted in a bid shall include all items of labor, materials, tools, equipment and other
costs necessary to fully complete the manufacture and delivery of the completed SEWER
VACCUM TRUCK PURCHASE pursuant to the Bid Specifications. It is the intention of the Bid
Specifications to provide for and require a complete SEWER VACCUM TRUCK PURCHASE of
the type prescribed in the Bid Specifications and ready for operation by the City.
Any items omitted from the Bid Specifications which are clearly necessary for the completion and
operation of such equipment and its appurtenances shall be considered a portion of such equipment
although not directly specked or called for in the Bid Specifications.
All parts shall be new. In all cases,materials must be furnished as specified.
Acceptance of delivery of the SEWER VACUUM TRUCK PURCHASE shall not release the
successful contractor from liability for faulty design, workmanship or materials appearing even
after final payment has been made.
The City reserves the right and shall be at liberty to inspect all materials and workmanship at any
time during the manufacturing process and shall have the right to reject all materials and
workmanship which do not conform to the specifications. However, the City is under no duty to
make inspection, and if no inspection is made, the chosen contractor shall not be relieved of any
obligation to furnish materials and workmanship strictly in accordance with specifications.
BID SECURITY: To be considered, the bid must be accompanied by a bid security unconditionally
payable to the City of Bozeman for ten percent (10%) of the total amount of the bid and attached as
Exhibit 1 on the Bid Form. Each Bidder shall expressly covenant in the bid that if the Bidder is awarded
the bid,the Bidder will, within thirty(30)days after the bid is awarded, enter into a Purchase Agreement
with the City of Bozeman in substantially the same form as shown on the Purchase Agreement. Bid
1
security must be provided in a form specified in §18-1-203, MCA, which includes, but is not limited to,
certified check, cashier's check, bank draft, bid bond, guaranty bond, or surety bond. Bid security
through a bid, guaranty or surety bond must be issued by a surety company authorized to do business in
the State of Montana. The bid security protects and indemnifies the City against the failure or refusal of
the successful Bidder to timely enter into the Purchase Agreement.
SIGNATURE OF BIDDERS: Each bid must be signed in ink by the Bidder with the Bidder's full name
and business address or place of residence. If the Bidder is a firm or partnership,the name and residence
of each member must be inserted. If the bid is submitted by or in behalf of a corporation, it must be
signed in the name of the corporation by a corporate official authorized to bind the corporation and who
shall also affix the corporate seal of the corporation to the bid. Any bid by a corporation signed by a
person other than a corporate officer must be accompanied by a power of attorney showing that person's
authority to sign for the corporation.
ONLY ONE PROPOSAL: No Bidder may submit more than one bid. Two bids under different names
will not be received from one firm,partnership,association,or corporation.
RESPONSIBILITY OF AGENT: Any person signing a bid as the agent of another, or of others, may
be required to submit satisfactory evidence of authority to so sign.
TITLE: The position title of any person executing the bid or Agreement shall be clearly indicated
beneath the signature.
RESPONSIBLE BIDDER: Bidder is not deemed a responsible bidder if Bidder is delinquent in
payment of property taxes or special improvement district assessments within the City of Bozeman for at
least six(6)months.
Any Bidder required by the Bozeman Municipal Code to have a general business license in the City of
Bozeman must obtain such license before a bid can be awarded to a bidder.
EXAMINATION OF SPECIFICATIONS: Before submitting a bid, each Bidder should examine the
Bid Specifications,these Instructions to Bidders, the Bid Form, and the Purchase Agreement thoroughly
and become familiar with federal,state, and local laws,ordinances,rules,and regulations that may, in any
manner,affect the cost or delivery of the goods.
INTERPRETATION OF CONTRACT DOCUMENTS: If any person contemplating submission of a
bid for the proposed Purchase Agreement is in doubt as to the true meaning of any part of the
specifications, that person may submit a written request to the City for an interpretation thereof. The
person submitting the request will be responsible for its prompt delivery. Any interpretation of the
proposed purchase agreement will be made only by an addendum duly issued and a copy of any such
addendum will be mailed or delivered to each person receiving the specifications.
TIME OF COMPLETION: The time of delivery of the goods to be purchased is a basic consideration
of the contract. It is necessary that each Bidder satisfy the City of the Bidder's ability to deliver the goods
being purchased within the stipulated time.
ADDENDA: If applicable, any addenda issued during the time of bidding, or forming a part of the
specifications provided to Bidder for the preparation of Bidder's proposal, shall be covered in the bid and
shall be made a part of the Purchase Agreement. Receipt of each addendum shall be acknowledged in the
bid. Any bid in which all issued addenda are not acknowledged will be considered incomplete and will
not be read.
WITHDRAWAL OF BID: No Bidder may withdraw any bid for a period as specified in the Invitation
to Bid after the date and hour set for the opening declared herein. Prior to that time, Bidder may
2
withdraw a bid by written request. The request to withdraw a bid must be signed in the same manner and
by the same person or persons who signed the bid.
ACCEPTANCE AND REJECTION OF BIDS: The City reserves the right to accept or reject the bids
in the best interest of the City. The City reserves the right to waive informalities and irregularities in any
bid submitted, to reject non-conforming, non-responsive or conditional bids, to correct arithmetic errors
without changing unit price, and postpone awarding of the Purchase Agreement for a period not
exceeding sixty(60)days.
AWARD OF BID: If the bid is to be awarded, City will award the bid to the responsible Bidder whose
bid is responsive and conforms to all material terms and conditions of the bidding documents and
proposed Purchase Agreement, is lowest in price, is in the best interest of the project, and other factors
considered. The award will be based on the lowest responsive cumulative base bid plus any added
alternate schedules the City determines to include with the project. If the bid is awarded, the award will
be made within the period specified in the Purchase Agreement. The successful Bidder will be notified
by letter mailed to the address shown on the bid that the bid has been accepted and that Bidder has been
awarded the bid.
CANCELLATION OF AWARD: The City reserves the right to cancel the award of any bid at any time
before the complete execution of the Purchase Agreement by all parties without any liability against the
City.
EXECUTION AND APPROVAL OF AGREEMENT: The Purchase Agreement shall be signed by
the successful Bidder and returned within the time shown on the bid. If the Purchase Agreement is not
executed by the City within fifteen (15) days following receipt from Bidder of the signed Agreement,
Bidder has the right to withdraw the bid without penalty. The Purchase Agreement is not effective until it
has been fully executed by all of the parties thereto.
FAILURE TO EXECUTE AGREEMENT: Failure to execute the Purchase Agreement shall be just
cause for annulment of the award. In the event of such annulment,the bid guarantee shall be forfeited to
the City, not as a penalty, but as liquidation of damages sustained. Award may then be made to the next
lowest responsible and qualified Bidder,or the project may be re-advertised as the City may decide.
PAYMENT: Payment for all goods purchased under the Purchase Agreement will be made by the City
within the time period specified in and in accordance with the procedures outlined therein.
NON-DISCRIMINATION: In accordance with law, each entity submitting a bid shall affirm on the
form provided by the City that the Bidder shall not discriminate in the performance of the work called for
in the Bid Specifications on the basis of race, color, religion, creed, sex, age, marital status, national
origin,or because of actual or perceived sexual orientation,gender identity or disability,with regard
to, but not limited to, the following: employment upgrading, demotion or transfer, recruitment or
recruitment advertising, layoff or termination, rates of pay or other forms of compensation, selection for
training,or rendition of services.
It is further understood that any vendor who is in violation of this clause shall be barred forthwith from
receiving awards of any purchase from the City of Bozeman unless a satisfactory showing is made that
discriminatory practices have ceased,and the recurrence of such acts is unlikely.
3
City of Bozeman, Montana
Water/Sewer Department
Bid Specifications and Bid Form
*Note: your bids must be submitted on this form.*
Bid Specifications for one (1) New 2014 or newer Sewer Vacuum Truck
The Sewer Vacuum Truck described herein shall be new 2014 or newer production and
be fully functional and shall be in first class running condition upon delivery. All parts and
accessories which are required to compose a complete unit shall be furnished whether herein
stipulated or not. Unless otherwise noted in these specifications, all equipment cataloged as
standard shall be furnished and included in the purchase price of the unit.
Any changes from Standard features must be shown on the manufacturer's
specification sheet that must be included in the bid. The City of Bozeman reserves the right to
accept or reject any or all bids for any reason determined to be in the best interest to the City of
Bozeman. The Sewer Vacuum Truck must be one that the City of Bozeman has owned or has
had an onsite demonstration with the equipment at our facility. We will not consider bids of
brands we have never owned or demonstrated. The complete truck must be delivered on site
within nine (9) months of the order date. Delivery charges will be included in final bid price.
Section 1 General
The truck shall be a fully functioning sewer vacuum truck capable of using high pressure water
to remove common debris found in storm and sanitary sewers including sand, gravel, grease
and root masses. Any component not included in this bid specification that is required to
provide a fully functional unit must be included. Also, any feature or component that is
"standard"to the manufacturer's truck or that appears to be standard per brochures or other
information provided must be included in the unit unless otherwise specified in this bid.
Yes x No Exceptions
Section 2 Sub Frame
The equipment shall be of modular design consisting of vacuum system, water tanks system,
debris body and drive system.
Yes_1 No Exceptions
A sub frame shall be fabricated to the exact dimensions of the truck chassis for mounting of
modular components.
Yes II No Exceptions
Bid SNrr ifications for or.e(1)new 201c or newer Sewer Vacuum Truck
All components of the module shall attach to the sub frame and not directly to the chassis.
Yes X No Exceptions
Sub frame shall be designed to ASME standards for maximum applied loads; chassis frame
movement and even distribution of weight to the chassis and suspension.
Yes No Exceptions
Sub frame shall be continuous and uninterrupted from back of cab to end of frame.
Yes X No Exceptions
Section 3 Debris Body
The body shall be cylindrical having a minimum usable liquid capacity of twelve (12) cubic
yards.
Yes 1-k No Exceptions
The body shall be capable of high dump height of sixty inches (60"); dump height of sixty inches
(60") must be achieved without the use of scissor lift mechanism.
Yes No Exceptions
The debris storage body shall be constructed with a minimum one forth inch (1/4") corrosion and
abrasion resistant Ex-Ten steel.
Yes X No Exceptions
The debris storage body shall have a minimum yield point of fifty thousand (50,000) PSI and a
minimum tensile strength of seventy thousand (70,000) PSI.
Yes X No Exceptions
Body shall have a rear door that is hinged at the top and is equipped with a replaceable
neoprene type seal; adjustable for periodic compensation of door seal wear.
Yes_� No Exceptions
Dual outward mounted rear door props shall be included as standard to prevent operator from
entering door swing path when engaging rear door prop.
Yes Y, No Exceptions
For optimal particulate separation, vacuum shall be drawn from separate ports in the top of the
debris body.
Yes Y` No Exceptions
Bid Specifications for one(1)new 2014 or newer Sewer VaCUUm Truck
Body shall be dumped by raising the body to a fifty (50) degree angle utilizing a forward
mounted, double acting hydraulic dump cylinder.
Yes No Exceptions
Dump controls, accessory controls, e-stop control shall be provided at a central curb side
location directly behind the cab of the truck.
Yes X No Exceptions
For stability and safety, dumping must be accomplished while the pivot point of the body
remains fixed to the sub frame.
Yes No Exceptions
Industrial style rear debris body door shall be flat, and shall open and close hydraulically by
cylinders mounted at the top of the body; door shall open fifty (50) degrees from the fully closed
position; door shall be unlocked, opened, closed, and locked by a failsafe hydraulically activated
sequential positive locking system; cam operated by a single hydraulic cylinder with all controls
located behind truck cab; forward of the debris body so operator is not subject to sewage when
dumping.
Yes No Exceptions
Debris body shall have a body flush out system with a fan-type spray nozzle located in the front
wall of the debris body to aid in the flushing of heavy debris; the nozzle shall also utilize two (2)
spray nozzles to flush the front most area of the debris body; system must produce a flow of
eighty (80) GPM; control valve shall be on the curb side of the unit.
Yes X No Exceptions
Body shall have a float type automatic shut-off system protecting the fan system with two (2) ten
inch (10") stainless steel shut-off balls located in the debris body; each float ball housing shall
be within a non corrosive slide-out screen assembly and be accessed without the use of tools.
Yes X No Exceptions
The debris body shall be equipped with a rear door drain to drain off excess liquids with an
internal screen to prevent large solids from passing; a manually operated six inch (6") knife
valve with cam-lock coupler and twenty five feet(25) of lay flat hose having cam lock quick
connects shall be included at this location.
Yes X No Exceptions
Debris body shall have four hundred fifty(450) GPM, three inch (3") submersible trash pump,
externally mounted in the forward body wall, with two and a half inch by twenty five feet (2 '/2" x
25') lay-flat hose, hose storage basket and three inch (3") shutoff lever gate valve; system shall
be turned on/off with selector valve at curbside controls.
Yes No Exceptions
ern Specrfir ations for ono(1)new 201.1 or newer Sewer Vacuum Truck
Four(4) dual vertical (cyclone) centrifugal separators shall be installed in-line between the
debris body and the air mover, two (2) per side for each debris body discharge port; each dual
separator shall include large fallout chamber cleanout door.
Yes Y- No Exceptions
Minimum of five (5) vacuum tubes shall be stored on curbside storage racks to minimize
operator exposure to traffic side of unit; shall include quick release retainer handles, no bungees
or clamps.
Yes I( No Exceptions
A curbside, folding three (3) pipe rack shall be provided, constructed of steel tubing, spring
assisted; shall include quick release retainer handles, no bungees or clamps
Yes I No Exceptions
A street side, folding three (3) pipe rack shall be provided, constructed of steel tubing, spring
assisted; shall include quick release retainer handles, no bungees or clamps
Yes No Exceptions
Two (2) pipe storage racks curbside waist level.
Yes No Exceptions
A splash shield shall be mounted around the lower sixty percent (60%) of door opening to direct
liquid and debris away from the chassis; shield shall be minimum ten inches (10") deep bolted
assembly with no openings.
Yes Y` No Exceptions
A lubrication manifold system shall be provided to allow ground level greasing of boom lift and
swing cylinders, float level indicator, top rear door hinges and debris body hoist cylinder pins.
Yes X No Exceptions
A ten inch (10") valve with three inch (3") vent to atmosphere, electrically activated, air operated
valve debris body vacuum relief system shall be located in the inlet of the vacuum system to
allow the venting of the tank and relieve vacuum at the debris intake hose.
Yes X No Exceptions
A debris inlet deflector distributing load evenly in debris body shall be included.
Yes X No Exceptions
4
Bid Specifications for one(1)new 201 3 or newer Sewer Vacuum Truck
Section 4 Water Tanks
The water tanks shall be manufactured from a non-corrosive material to prevent rust yet still
provide for maximum strength.
Yes X No Exceptions
The water tank material shall require no internal coating and shall be repairable if patching is
required.
Yes �_ No Exceptions
The water tanks shall be easily removed from the sub-frame to provide complete access to the
truck chassis for maintenance purposes.
Yes I No Exceptions
The water tanks shall be adequately vented and connected to provide complete filling.
Yes�_ No Exceptions
The water tanks shall be totally separate from the debris tanks and provide no structural
support.
Yes _ No Exceptions
The water tanks shall share no common walls with the debris tanks to prevent corrosion.
Yes *)( No Exceptions
The water tanks shall come equipped with an anti-siphon device with two inch (2") male cam-
lock attached and twenty five feet (25') of hydrant fill hose and with two inch (2") female cam-
lock ends on both ends of hose.
Yes�_ No Exceptions
The water tanks shall carry a ten (10) year warranty against corrosion or cracking; exceptions of
requirement shall be explained in detail accompanied with detailed engineering drawings.
Yes X No Exceptions
All water tanks shall be fully baffled to form maximum compartment storage of one hundred fifty
(150) gallons for each compartment.
Yes X No Exceptions
The water tank shall be located for the lowest possible center of gravity while providing one
hundred percent (100%) gravity flooded intakes to water pump.
Yes No Exceptions
5
Rid Specifications for one(1)new 2014 or newer Sewer Vaeuum Truer
Fresh water shall enter the tanks through an in line six inch (6") air gap, all aluminum covered
anti-siphon device.
Yes X No Exceptions
Water level sight tubes of non-yellowing plastic shall be installed on both tanks.
Yes No Exceptions
The sides of these water tanks shall not extend more than forty eight inches (48") out from the
centerline of the truck chassis.
Yes X No Exceptions
A fresh water drain system shall be provided to completely drain the fresh water system from
one location utilizing a three (3) drain port and plug.
Yes Y. No Exceptions
A minimum six inch (6") connection between tanks shall be provided.
Yes 1� No Exceptions
The water tanks shall not elevate with debris body during dump cycle.
Yes X No Exceptions
A low water alarm with light at the operator station shall alert operator when water storage has
one hundred fifty (150) gallons remaining.
Yes X No Exceptions
A hydraulic oil high temperature light and alarm shall be provided.
Yes X No Exceptions
A three inch (3") in-line "Y"trap strainer shall be located at inlet of water tank fill air-gap.
Yes X No Exceptions
A three inch (3") in-line "Y" trap Monel stainless steel strainer shall be located between the
water cells and water pump.
Yes X No Exceptions
A three inch (3") gate valve shall be provided at water pump.
Yes No Exceptions
6
Bid Specifications for mu (1)new 2014 or newer Sewer vacuum Truck
Water tank must be a certified metered capacity of one thousand five hundred (1500) gallons.
Yes Y, No Exceptions
Water tanks shall be constructed of one eights inch (1/8") aluminum with baffled compartments
maximum one hundred fifty (150) gallons each.
Yes _ No Exceptions
Liquid Float Level Indicator shall be provided.
Yes X No Exceptions
Section 5 Vacuum/Vacuum Drive System
Vacuum shall be provided by compressing air within a two-stage thirty eight inch (38") diameter
centrifugal compressor.
Yes y No Exceptions
Compressor fans to be constructed of non-corrosive material.
Yes X No Exceptions
Each centrifugal compressor fan shall be constructed of non-corrosive, hardened one quarter
inch (1/4") chrome blades.
Yes X No Exceptions
Centrifugal compressor shall be warranted against corrosion for five (5) years.
Yes No Exceptions
The outer housing shall be constructed of one quarter inch (1/4") spun steel.
Yes X No Exceptions
Compressor housing shall be equipped with a fan flush out system drain not exceeding two
inches (2") diameter.
Yes No Exceptions
Complete compressor and housing assembly shall be warranted against materials and
workmanship for five (5) years.
Yes �` No Exceptions
7
Bid Spec fu:atiom for one(1)new 2014 or newer Sewer Vacuum Truck
Hydrostatic drive system that shall include an electronic controlled variable displacement
hydrostatic pump producing up to three hundred (300) Bar.
Yes Y, No Exceptions
The compressor hydrostatic drive system shall utilize electronic controls located at the front
operator station; the system shall be controlled on/off with a switch that may be engaged or
disengaged at any operating speed.
Yes X No Exceptions
The compressor controls will have a speed selection switch at the operator station to control
compressor speed; manual levers on the hydrostatic pump to control compressor speed will not
be accepted.
Yes X No Exceptions
The centrifugal compressor should be driven direct through a helical gear type step-up
transmission drive with a step-up ratio of two (2) to one (1).
Yes No Exceptions
Hydraulic shut off valves shall be provided at the suction, return and filter lines to permit
servicing of the hydraulic system.
Yes X No Exceptions
The drive shaft shall be supported via ball bearings and gears.
Yes X No Exceptions
Compressor shall be driven from a closed loop hydrostatic drive system utilizing available
chassis power via split-shaft transfer case; the transfer case shall drive a variable displacement
hydrostatic pump to energize a closed loop.
Yes X No Exceptions
The pump shall be mounted directly to the split shift transfer case; the pump will have a B10 life
rating of ten thousand (10,000) hours continuous duty.
Yes No Exceptions
The hydraulic motor powering the compressor shall be a bent axis, bi-directional motor; motor
speed shall not exceed two thousand five hundred (2,500) RPM.
Yes It, No Exceptions
The hydrostatic drive system shall utilize electronic soft start speed control to manage ramping
speed.
Yes X No Exceptions
Bid Specifications For one(1)new 2014 or newer Sower Vacuum Truck
The control system shall provide a mode selection switch to control the compression drive in low
vacuum, combination mode and full vacuum settings.
Yes�^ No Exceptions
The gear drive should attach directly to the rotor shaft without the use of multiple stage V-belts
or jack shafts.
Yes No Exceptions
The gears and bearings shall be lubricated with splash lubrication system, requiring no manual
greasing.
Yes X No Exceptions
The drive system shall not utilize pillow block bearings.
Yes X No Exceptions
Section 6 Vacuum Boom System
Vacuum hose shall be designed for front operation with hose mounted and stored at front
mounted work station; front mounted location is required for ease of positioning vacuum hose as
well as minimizing need for operator to swing hose into traffic.
Yes_ Ic No Exceptions
All connections between debris body and vacuum system will be of the self-adjusting pressure
fitting type.
Yes ( No Exceptions
Vacuum hose will remain stationary and not rise with debris body.
Yes X No Exceptions
Upper debris tube shall consist of an anchored steel tube and elbow.
Yes X No Exceptions
A sub-frame mounted cab guard shall be mounted behind cab with boom rest cradle.
Yes Y, No Exceptions
All vacuum pipes shall be connected to vacuum pick up tube and extension pipes by adjustable
over-center quick clamps to join the aluminum flanges on pipes.
Yes No Exceptions
q
Bid Spec ifiranons for ore(1)new 2014 or newer Sewer Vacuum Truck
One (1) quick clamp for each pipe supplied shall be provided.
Yes No Exceptions
Boom pedestal shall be directly mounted to module sub-frame.
Yes X No Exceptions
Boom support used for travel mode shall not interfere with access or require removal to tilt hood
forward.
Yes�_ No Exceptions
A control station shall be equipped with control switches for all directions as well as a safety
emergency shut-down button, which shall automatically eliminate power to boom.
Yes No Exceptions
The vacuum boom shall have a heavy-duty flexible hose assembly joining the transition pipe to
the debris body, and a seventy (70) degree elbow and five and one half(51/) heavy duty hose at
the suction end of the boom.
Yes ( No Exceptions
Boom shall rotate one hundred eighty (180) degrees and shall be operated by an electric over
hydraulic system; lift and swing movements shall be actuated by hydraulic cylinders.
Yes X No Exceptions
The horizontal inner steel vacuum tube and inner box beam boom section shall telescope (tube
within tube, box beam within box beam) and retract a minimum of eight feet (8') without affecting
the vertical position of the pick-up tubes, and shall be located at the front work station in its
retracted position, providing two hundred twenty seven inches (277") minimum reach off the
longitudinal axis of unit.
Yes X No Exceptions
Boom shall be fully controlled by a remote push button pendant control station with twenty five
foot (26) cable; controls to include up/down, lefUright, in/out boom functions, vacuum relief, e-
stop and main power switch.
Yes X No Exceptions
A joystick for hydraulic control of the boom shall be installed on hose reel front panel.
Yes No Exceptions
Removable four inch (4") diameter storage "Post" to stabilize the lower boom hose during
transport; storage device shall not interfere with raising hood.
Yes X No Exceptions
10
Bid Specihcations for one(1)new 2014 or newer Sewer VaIUUm Truct;
A cordless remote boom control system equipped to activate boom functions, throttle, water
pump on/off, hose reel in/out, hose reel speed, vacuum relief on/off and emergency
disengagement e-stop shall be provided.
Yes No Exceptions
A rotatable inlet hose for telescopic boom shall be provided.
Yes X No Exceptions
A detailed engineering drawing must be supplied showing the relationship of the hose reel in
relation with the vacuum boom range of motion; drawing shall show module mounted on
chassis, full arc of vacuum hose both retracted and extended, full rotation of arc for hose reel in
the extended position and dimension all arc lengths of vacuum boom retracted and extended;
drawing shall highlight intersection areas whereby combination cleaning is possible within full
arc on telescoping boom system.
Yes No Exceptions
Section 7 Water Pump and Drive
For most efficient use of horsepower and reduced fuel consumption, high pressure rodder pump
shall be hydraulically driven via one (1) load sensing utility pump, one (1) variable displacement
pump and one (1)fixed displacement pump.
Yes X No Exceptions
Hydraulic powered rodder pump via twin variable displacement hydraulic pumps and one (1)
fixed displacement utilizing two (2) ten (10) bolt PTO's.
Yes X No Exceptions
High pressure water pump shall be rated capable of continuous delivery of eighty (80) GPM at
two thousand five hundred (2500) PSI; submit manufacturer support documentation.
Yes X No Exceptions
High-pressure water(rodder) pump system shall allow front-mounted controls for operation of
three (3) modes: one (1) Low flow range zero to twenty two (0-22) GPM; two (2) medium-flow
range, twenty two to sixty (22-60) GPM/two thousand five hundred (2500) PSI; and three (3)
high-flow range: sixty (60) up to eighty (80) GPM/two thousand five hundred (2500) PSI.
Yes No Exceptions
Digital flow meter shall be displayed in front LCD display; flow meter shall be capable of
displaying system flow in all pump operating modes; a low water alarm shall be provided.
Yes X No Exceptions
11
Bid Specifications for one(1)new 2014 or newer Sewer Vacuum truck
This hydraulic drive system shall allow variation of water pump speed independent of required
vacuum drive speed within maximum drive engine speed of one thousand seven hundred sixty
(1760) RPM.
Yes�_ No Exceptions
Variable flow systems routing water back-to-tank are not considered equal due to additional
wear, horsepower and fuel consumption; any deviation from this drive requirement should have
full explanation of horsepower consumption.
Yes X No Exceptions
Water(rodder) pump shall include smooth and pulsation operation mode feature.
Yes X No Exceptions
When required to assist nozzle breaking through obstructions, water pump "pulsation mode"
shall provide a forward-acting nozzle surge; pulsation surge wave shall allow nozzle to punch
forward two inch (2") to eighteen inch (18") depending on flow dynamics and length of hose in
sewer pipe.
Yes % No Exceptions
Water pump location shall provide a flooded gravity suction inlet to eliminate potential
cavitations damage.
Yes X No Exceptions
An oil to water heat exchanger will be provided in the water system to cool all hydraulic fluids on
the unit. State horsepower requirement to operate hydraulics at full speed:
Yes X No Exceptions
The water pump shall provide precise zero to eighty (0-80) GPM controlled flow at variable
pressure up to two thousand five hundred (2500) PSI.
Yes X No Exceptions
An extreme cold weather recirculation system - minimum twenty five (25) GPM via transmission
PTO at chassis engine idle speed.
Yes x No Exceptions
A hydro-pneumatic nitrogen charged accumulator system shall be provided with all control
valves, piping and hoses for either continuous flow or jackhammer rodding; accumulator shall
be a two point five (2.5) gallon capacity and one thousand four hundred (1400) to two thousand
five hundred (2500) PSI pressure rating.
Yes X No Exceptions
12
Bid Spec ifications for on a(1)new,2014 or newer Sewer Vaci.iurn rrurk
Two (2) one half inch (1/2") high pressure ball valves shall be provided for draining the water
pump and flushing sediment from the bottom of the pump.
Yes X No Exceptions
A nozzle rack accommodating three (3) nozzles shall be provided in curbside toolbox; the
nozzles shall be labeled on storage rack for pipe size/flow and application.
Yes X No Exceptions
System shall be relieved to protect operator.
Yes X No Exceptions
Handgun shall be supplied that allows for changing of flow pattern from a fine mist to a steady
stream.
Yes ( No Exceptions
Handgun shall come equipped with quick connect couplers.
Yes No Exceptions
An additional one inch (1")water relief valve shall be provided.
Yes Y, No Exceptions
A mid-ship quick disconnect handgun couplers shall be provided.
Yes K No Exceptions
Front and rear quick disconnect handgun couplers shall be provided.
Yes X No Exceptions
Hydro-Excavation Package/Retractable Reel with fifty foot by three eights inch (50' x 3/8")
Hose, Hydro excavation Handgun and Plumbing;water system shall allow precise variable flow
control range of zero to twenty two (0-22) GPM at two thousand five hundred (2500) PSI with
digital flow meter in clear view of adjustment control.
Yes X No Exceptions
A water pump hour meter shall be provided.
Yes `l� No Exceptions
13
Bid Shy,ifications For one(l)new 2014 or newer Sevier Vacuum Truck
Section 8 Hose Reel
Hose reel assembly shall be direct frame mounted.
Yes No Exceptions
Hose reel assembly shall be mounted on an independent frame that can be removed from
brackets attached permanently to front of main truck frame members.
Yes�_ No Exceptions
Reel will be manufactured out of one quarter inch (1/4") spun steel for added structural strength
and shall require no internal or external reinforcements that could damage rodder hose.
Yes X No Exceptions
Hose reel shall be driven by adjustable gear reduction chain and sprocket assembly.
Yes _ No Exceptions
Hose reel shall operate at full rotational speed while chassis engine is at idle.
Yes X No Exceptions
Hydraulic Telescoping Rotating Hose Reel—eight hundred foot (800') capacity of one inch (1")
hose shall be provided.
Yes I No Exceptions
The front mounted hose reel shall telescope fifteen inches (15")forward down centerline of
truck.
Yes X No Exceptions
Entire reel assembly shall rotate two hundred seventy (270) degrees on a large diameter ball
bearing.
Yes No Exceptions
Hose reel shall include a dual locking device to positively lock reel in any position across
operating range.
Yes X No Exceptions
The hose reel shall rotate about the reel assembly centerline so the reel shall never extend
beyond the truck width; reel coverage diagram shall be submitted with bid.
Yes y' No Exceptions
14
Bid Spe(ificaIions for one(1)new 20,14 or newer Sewer Vacuum Truck
Controls shall be accessible on both sides of the hose reel, allowing operator to work at either
side of unit for safety purposes.
Yes No Exceptions
Eight hundred foot by 1 inch (800' x 1") Piranha Sewer Hose/two thousand five hundred (2500)
PSI shall be provided.
Yes X No Exceptions
An air-cylinder actuated pinch-roller shall exert downward pressure across full width of reel to
retain hose on reel when encountering nozzle blockages.
Yes X No Exceptions
A hose footage counter shall be supplied to indicate the amount of hose travel within pipe.
Yes X No Exceptions
Digital footage counter displaying absolute and relative footage values shall be provided;
system must be capable of resetting relative value to ensure operator safety; accuracy to within
one percent (1%) of actual distance; large easy to read LCD screen, large keypad with sealed
membrane switches that are easily activated,Nema-4 Moisture Sealed Enclosure ,Solid State
Circuitry ,Dimensions: five and five eights by three and three eights by three sixteenth (5 5/8 X 3
3/8 X 3116), LCD display area: three point zero by two point two (3.0 X 2.2)
Yes 1. No Exceptions
Section 9 Wash Down Equipment
A spring retractable storage reel for handgun hose shall be provided to allow the operator to
deliver water to area served by pick up hose and to the inside of the debris body for clean out;
reel shall be mounted mid-ship on curbside, equipped with one half by fifty foot (1/2 x 50') two
thousand (2000) PSI hose; an additional thirty five feet (35') of one half inch (1/2") hose with
quick disconnect couplers shall be supplied loose.
Yes -)( No Exceptions
Hand sprayer with adjustable spray-pattern to be provided with trigger-style gun.
Yes No Exceptions
Section 10 Front Operating Station and Controls
Primary operator station will be located at front of truck on right curb side of hose reel.
Yes No Exceptions
1�
Bid Spodficauonn for one(1)new 2014 or o,%vor Sewer Vacuum Truck
All front operator controls shall be accessible while operating either front or rear side of reel
assembly; all operations to either side of unit shall position operator in front of vehicle affording
protection from oncoming traffic.
Yes X No Exceptions
Station shall include truck engine throttle, water pump (on/off), water pump mode, water pump
flow meter, hose reel control valve (forward/reverse), adjustable hose reel speed control, oil
dampened water pressure gauge, boom controls, digital water pump flow meter, and low water
warning light.
Yes�_ No Exceptions
Tachometer and hour meter for chassis engine provided at control station shall be provided.
Yes X No Exceptions
All Hydraulic Functions- Color Coded, Sealed Electric/Hydraulic NEMA four (4) switches shall
be provided.
Yes ')( — No Exceptions
Fan Engagement/Vacuum Relief- Sealed Electric/Air NEMA four(4) Switch shall be provided.
Yes No Exceptions
Water pump hour meter shall be provided.
Yes X No Exceptions
PTO hour meter shall be provided.
Yes X No Exceptions
A temperature light and alarm shall be provided; light and alarm will be activated when hydraulic
temperature reaches one hundred eighty (180) F.
Yes X No Exceptions
Section 11 Electrical and Safety Lighting
The entire system shall be vapor sealed to eliminate moisture damage, "Nema-4" type or equal.
Yes X No Exceptions
16
Bud Specifications for one(1)new 2014 or newer Sewer Vacuum Truck
Vansco Electronic Package: Chassis Tachometer, Auxiliary Engine Tachometer, Operating
Mode, PTO Mode, Hydraulic Oil Temperature shutdown, and E-Stop shall be included; E-Stop
activation must turn off rodder pump, shutdown PTO A & B, set chassis throttle to idle, & open
vacuum relief; E-stop must be located at each operator interface; including front/rear hose reel
controls, pendant control, & dump control location; basic machine functions and both chassis
and module diagnostics shall be provided.
Yes No Exceptions
All electrical connections shall be void of exposed wires or terminals nor should they be painted;
paint process shall be completed prior to installation of wiring.
Yes X No Exceptions
All wiring shall be color-coded and encased in conduit to scaled terminal boxes with circuit
breakers.
Yes No Exceptions
All light bulbs shall be shock mounted.
Yes X No Exceptions
All other lights required by State and Federal Laws.
Yes X No Exceptions
A pistol grip hand light with bumper plug and twenty five foot (25') coiled cord shall be provided.
Yes y No Exceptions
Operator station work lights shall be provided
Yes X No Exceptions
Hose reel manhole work lights shall be provided
Yes X No Exceptions
Two (2) LED boom work lights shall be provided.
Yes X No Exceptions
LED work light at mid-ship curbside shall be provided.
Yes X No Exceptions
Two (2) LED rear door work lights shall be provided
Yes X No Exceptions
__ _ _ 17
Bid Specifications for one(1)new 2014 or newer Sewer Vacuum Truck
LED lights, clearance, back-up, stop, tail and turn shall be provided.
Yes X No Exceptions
Six (6) LED light system; two (2) mirror mount strobes, two (2) mid-ship, two (2) rear mount oval
LED quad flash strobes; Part numbers include Federal Signal 607101-02, Target Tech 601601
and Target Tech 416104.
Yes X No Exceptions
Signal — Master Direction Arrow Stick one (1) piece eight(8) LED rear lights; Federal Signal part
numbers 320795 and 320782.
Yes X No Exceptions
Section 12—Safety Equipment
E-stop shall be located at each operator interface location; standard locations to include: front
hose reel, mid-ship curbside dump controls, &wireless controller (if equipped.)
Yes�_ No Exceptions
Electrical system controls shall be configured to allow for single point operation only; upon
engagement of controls at specified locations, additional controls shall be disabled.
Yes X No Exceptions
Electrical system must enable self-check to ensure all switches are in home position prior to
critical function enablement; system must "lock out" controls when switch is not in home position
Yes_� No Exceptions
Rear work lights shall be activated upon engagement of reverse gear.
Yes No Exceptions
One (1) Emergency Flare Kit shall be provided
Yes X No Exceptions
Seven Inch (7") dash monitor, two (2) camera system shall be provided; a front hose reel color
camera with one hundred thirty (130) degree viewing angle shall be provided to provide a front
visual of the manhole cover to aid in equipment set-up; a rear back-up color camera with one
hundred thirty (130) degree viewing angle shall be provided; camera to have automatic
activation when the unit is switched to reverse.
Yes x No Exceptions
IS
Bid Spenficahons for or P(1) iev,201,1 or•iawer Sewer Vacuum Truck
Section 13—Sewer Tools and Accessories
One (1) thirty (30) sand nozzle
Yes X No Exceptions
One (1) thirty (30) degree sanitary nozzle
Yes X No Exceptions
One (1)fifteen (15) degree penetrator nozzle
Yes X No Exceptions
One (1) one inch (1") small finned nozzle pipe skid
Yes X No Exceptions
Section 14—Vacuum Tools and Accessories
One (1) eight inch by three foot (8" x 3') aluminum pipe
Yes No Exceptions
Two (2) eight inch by five foot(8"x 5') aluminum pipe
Yes X No Exceptions
One (1) eight inch by six foot six inch (8" x 6'6") catch basin tube
Yes Y, No Exceptions
Four(4) eight inch (8") quick clamps
Yes X No Exceptions
Section 15—Chassis Equipment and Storage
Two(2)front tow hooks shall be provided.
Yes X No Exceptions
Two(2) rear tow hooks shall be provided.
Yes X No Exceptions
One(1) aluminum toolbox behind cab
Yes No Exceptions
19
Rio SpeuficaIions hx ore(1)new201:or newer Sawer Vacuum Tr(:(
One(1) aluminum toolbox with nozzle storage and dump controls mounted curbside shall be provided.
Yes�_ No Exceptions
Two(2) eighteen inch by sixteen inch by twelve inch (18"x16"x12") aluminum toolbox at front bumper
shall be provided.
Yes No Exceptions
One(1)twenty four inch by twenty four inch by twenty four inch (24"x24"x24") aluminum toolbox mounted
street side shall be provided.
Yes X No Exceptions
Section 16—Module Finish
Painting of the module shall be with a DuPont Imron Elite Polyurethane Enamel Top Coat.
Application is to be a wet top coat applied to a wet unsanded primer base.
Yes X No Exceptions
Module will be Dupont N4636 Blue and truck cab to be white.
Yes X No Exceptions
Section 17—SBA Conventional Truck
GVWR sixty six thousand (66,000) pounds.
Yes No Exceptions
Sloped Hood.
Yes No Exceptions
Designed for Vacuum Tank.
Yes y` No Exceptions
Cab to axle shall be a minimum of one hundred ninety three inches (193"); chassis supplier to
provide actual layout of chassis configuration.
Yes X No Exceptions
Section 18 - Engine
Minimum eight point nine liter(8.9L) SCR 2013 EPA emission engine.
Yes No Exceptions
Bid Speuficat1on5 for one(1)new 2014 or newer Sewer Vacuum rruck
Horse Power shall be three hundred seventy pound (3701b)/one thousand two hundred fifty foot
(1250ft) torque.
Yes Y— No Exceptions
Fuel filter shall be Water separator FS1003 with water in fuel sensor
Yes No Exceptions
Fuel cooler for single fuel tanks.
Yes No Exceptions
Immersion block heater one hundred twenty volt (120V) one thousand watt (1000W) with plug
under door.
Yes X No Exceptions
Alternator shall be Bosch one hundred sixty (160) amp brush type.
Yes X No Exceptions _?a►ccgf t6o 4MD brws1% *jK
Batteries shall be two (2) GP31 Threaded post one hundred (100) CCA each for a minimum of
two thousand (2000) CCA starting.
Yes X No Exceptions
Starter shall be twelve (12) volt electrical system.
Yes y No Exceptions
Multi-function engine connector for body builder.
Yes X No Exceptions
Air compressor shall be eighteen point seven (18.7) CFM or equal.
Yes X No Exceptions
Air cleaner shall be engine mounted
Yes �_ No Exceptions
Fan Hub shall be two (2) Speed Horton or equal.
Yes No Exceptions
?I
Bid Specifications for one(1)new 201�:or newer Sewer Vacuum Truck
Section 19 -Cooling module:
Radiator shall be minimum one thousand three hundred (1300) square inches
Yes X No Exceptions
Radiator shall have bug screen on front of grille
Yes Y, No Exceptions
Section 20 - Exhaust:
Shall be on Right hand side under cab SCR with right hand SOC vertical tailpipe.
Yes _ No Exceptions
Tailpipe shall be five (5) inch single eighteen (18) inch forty five (45) degree curved.
Yes X — No Exceptions
Section 21 -Transmission:
Shall be Allison three thousand (3000) RDS six (6) Speed with PTO Drive Gear.
Yes X No Exceptions
Torque Converter included with Allison Transmission.
Yes X No Exceptions
Allison fifth (5lh) Generation RDS package one hundred seventy two (172) for three thousand
(3000).
Yes X No Exceptions
Driveline shall be three (3) IVIED duty two (2) center bearings.
Yes X No Exceptions
Chassis shall have clearance for left hand and right hand transmission PTO.
Yes No Exceptions
Shall have severe service rear transmission support.
Yes X No Exceptions
Fid Spec if it at ions for one(1)new 201•'or newer Sewer Vacuum Truck
Allison Vocational Package 223.
Yes No Exceptions
Allison Vocational rating for on/off highway applications available with all product families
Yes X No Exceptions
Primary mode gears, lowest gear one (1), start gear one (1), highest gear six (6).
Yes No Exceptions
Secondary mode gears, lowest gear one (1), start gear one (1), highest gear six (6).
Yes X No Exceptions
Vehicle interface wiring and PDM with body builder connector at end of frame.
Yes X No Exceptions
Customer installed Chelsea 277 series PTO.
Yes�_ No Exceptions
PTO mounting shall be left hand side of main transmission.
Yes C No Exceptions
Magnetic plugs, engine drain, transmission drain, axle(s) fill and drain.
Yes _ No Exceptions
Push button electronic shift control shall be dash mounted.
Yes I No Exceptions
Transmission prognostics.
Yes X No Exceptions
Water to oil transmission cooler in radiator end tank.
Yes X No Exceptions
Section 22 - Front Axle: twenty thousand pounds (20,OOOlbs)
Dana Spicer D2000 Front Axle rated at twenty thousand (20,000) or equal.
Yes No Exceptions
Bid Specification~fo,one)1)ne<v 201.:of ne^-er Stwor VatUi'm True'.
All steer axle components meet or exceed requested axle rating.
Yes X No Exceptions
Front brake shall be twenty two thousand pounds (22,000lbs) Bendix sixteen and one half inch
by six inch (16-1/2"x6"); Brake assembly shall be ES s-cam or equal.
Yes C No Exceptions
Front Brake Drum shall be twenty thousand pounds (20,000lbs) sixteen and one half inch by six
inch (16-1/2x6") cast.
Yes X No Exceptions
Front Hub shall be twenty thousand pounds (20,000lbs) iron hub pilot.
Yes X No Exceptions
Front low maintenance hub package; Dana Spicer or equal with vented hubcap.
Yes X No Exceptions
Front auto slack adjuster.
Yes X No Exceptions
Front Springs taper leaf twenty thousand (20,000) with shock absorbers.
Yes�_ No Exceptions
Dual power steering gear; twenty thousand (20,000) dual.
Yes No Exceptions
Power Steering Cooler shall be radiator mounted air to oil.
Yes X No Exceptions
Front frame raised one inch (1").
Yes X No Exceptions
Section 23 - Rear Axle: forty six thousand pounds (46,000lbs) heavy wall axle housing
Dual Dana Spicer D46-170HP rear axle rated at forty six thousand (46,000) or equal.
Yes Y. No Exceptions
24
Bid S per M(dtinm fo;one(1) )ew 2014 or nevverSevre,Va,uum truck
Axle housing must be a minimum of one half inch (1/2") thick at spring seat.
Yes_� No Exceptions
All drive axle components meet or exceed requested axle rating.
Yes X No Exceptions
Rear Axle Ratio shall be six point eight three (6.83).
Yes X No Exceptions
Dual Rear Brakes shall be sixteen and one half by seven inch (16-1/2x7") to forty six thousand
(46,000).
Yes X No Exceptions
Dual Rear Brake Drums shall be cast.
Yes_ c No Exceptions
Dual Rear Hubs shall be iron hub pilot to forty six thousand (46,000).
Yes X No Exceptions
Longer studs for aluminum wheels with steel hub pilot wheels.
Yes X No Exceptions
Dual rear low maintenance hub package Dana or equal.
Yes X No Exceptions
Dual Rear axle automatic slack adjusters.
Yes X No Exceptions
Spring Brake three thousand thirty (3030) high output dual.
Yes_� No Exceptions
Bendix 4S/4M anti-lock brake system or equal.
Yes X No Exceptions
Rear suspension shall be Hendrickson RT463 forty six thousand (46,000) fifty four inch (54")
axle spacing; six inch (T) saddle height
Yes_ No Exceptions
Bid Spt�cificatiooi for onr(1)new 2014 or nFwer St-wer Vacuum Truck
Shall have steel beam and barpin bushing.
Yes C No Exceptions
Section 24-Tires &Wheels:
Front tires shall be Bridgestone M860 315/80R22.5 20PR rated to meet or exceed minimum
axle rating or equal.
Yes�c _ No Exceptions
Rear tires shall be Bridgestone M726EL 11 R22.5 14PR or equal.
Yes No Exceptions M-ICM 100a5 167i'l
Rear tire quantity shall be eight (8) tires.
Yes X — No Exceptions
Front wheel shall be Alcoa twenty two point five by nine (22.5x9) aluminum hub pilot rated ten
thousand pounds (10,0001-B).
Yes No Exceptions
Rear wheels shall be Alcoa twenty two point five by eight point two five (22.5x8.25) outer
wheels; inner wheels shall be Accuride 50408PKRPW white twenty two point five by eight point
two five (22.5x8.25) steel or equal.
Yes_ No Exceptions
Rear wheel rim quantity shall be eight (8)
Yes X No Exceptions
Section 25 - Frame:
Frame rails steel shall be ten and five eighths by three and one half by five sixteenth inch (10-
5/8 x 3-1/2 x 5/16").
Yes I No Exceptions
Shall have full steel inserts for frame rail.
Yes_ C No Exceptions
Delete front bumper.
Yes No Exceptions
26
dia Sprcificabonsfor ono(1(new 2014 or newer Sewer VaClnlnl Trud,
Custom frame layout shall be provided to body builder.
Yes X No Exceptions
Cantilever style battery box shall be located on the left hand back of cab.
Yes )k No Exceptions
Battery box to be mounted as close to left hand fuel tank as possible.
Yes X No Exceptions
Square end of frame
Yes X No Exceptions
Special frame drilling drawing to be provided by body manufacture mounting.
Yes X No Exceptions
Front mud flaps shall be installed.
Yes X No Exceptions
Aluminum non-polished right hand DPF/SCR cover.
Yes )( No Exceptions
Rear mud flap arms shall be Betts B-25 standard-duty.
Yes X No Exceptions
Rear mud flap shields shall be white plastic anti-sail.
Yes X No Exceptions
Section 26 - Fuel Tanks & Equipment:
Fuel tank shall be ninety (90) US gallon twenty eight point five inch (28.5") aluminum under or
equal.
Yes X No Exceptions
Welded in fitting with gasket and cover plate for mounting customer installed fuel tank heater.
Yes X No Exceptions
Location of ninety (90) gal fuel tank shall be left hand under cab.
Yes X No Exceptions
?7
,Rid Specifiration,for one(I)new 2014 or newer Sewer Vacuum Truck
Section 27 - Cab
Curved glass conventional cab shall be of aluminum sheet and post construction with fiberglass
roof cap and fully huck bolted.
Yes�_ No Exceptions
One piece curved windshield shall be rope in style glass.
Yes X No Exceptions
Doors shall be all aluminum three inch (3") bulkhead style daylite type construction.
Yes No Exceptions
Doors shall have a one (1) piece stainless steel piano style door hinge.
Yes X No Exceptions
Right hand door shall have a peeper widow.
Yes % No Exceptions
Door seals shall be mounted to the door and not the cab.
Yes No Exceptions
Hood shall be sloped hood with hood mounted grille with split fenders and mud flaps.
Yes X No Exceptions
Cab heater with integral defrosters, A/C, and forty five thousand (45,000) BTU heater
Yes X No Exceptions
Steering column shall be tilt-telescope with eighteen (18) inch four (4) spoke wheel.
Yes X No Exceptions
Thirty (30) AMP power lead with ground; wired through ignition accessory to behind rider seat.
Yes X No Exceptions
Instrument package includes speedometer, tachometer and outside temperature indicator.
Yes X No Exceptions
Bid Speuiications for one(1)new 2014 or newer Sewer Vacuum TrUd.
Instruments shall include a driver information center:
Yes No Exceptions
Large flat panel on dash for customer installed controls.
Yes No Exceptions
Cab interior shall be of manufactures standard level.
Yes�_ No Exceptions
Interior color shall be Slate Gray or manufactures standard color.
Yes _ No Exceptions
Driver seat shall be High Back air ride.
Yes I _ No Exceptions
Rider seat shall be air ride high back to match driver seat.
Yes X No Exceptions
Seat color shall be equal to standard color.
Yes No Exceptions
Radio shall be AM/FM.
Yes X No Exceptions
Under dash console-with two (2) power outlets.
Yes X No Exceptions
CB installation kit shall be center mounted of header.
Yes X No Exceptions
Two inch (2")fender extensions.
Yes X No Exceptions
Non-self cancelling turn signal switch column-mounted.
Yes x No Exceptions
Electric left hand and right hand door locks.
Yes X No Exceptions
R[d cpp,if,rations iot or,e(!)new 2014 or nemm Sewer Vacuum Truck
Minimum of thirty six inch (36") long grab handle right hand side of cab for access.
Yes No Exceptions
Minimum of thirty six inch (36") long grab handle left hand side of cab for access.
Yes X No Exceptions
Grab handle mounted left hand inside door frame above dash.
Yes_ No Exceptions
Grab handle mounted right hand inside door frame above dash.
Yes�_ No Exceptions
Single air horn under cab.
Yes X No Exceptions
Access steps mounted to fuel tank and DPF/SCR must have holes considered self cleaning.
Yes 1�1 No Exceptions
Electric-powered right and left hand door window
Yes�_ No Exceptions
Two (2) corner windows mounted in cab corners for additional visibility along with a minimum
seventeen inch by thirty six inch (17"x36") rear stationary window.
Yes�_ No Exceptions
Exterior Stainless steel sun visor.
Yes No Exceptions
Air ride cab suspension.
Yes X No Exceptions
Quiet cab package/Arctic package
Yes X No Exceptions
Section 28 - Mirrors:
Dual lighted heated mirrors seven inch by sixteen inch (7"x16").
Yes_k No Exceptions
30
Ezur St,!-nf r annns for ci,o(1)new 2014 ur new.-r Sower Vaf11Ur1 Tru,r.
Dual eight point five inch (8.5") offset heated convex mirror mount below regular mirror brackets.
Yes �_ No Exceptions
Single convex mirror eight and one half inch by four and seven sixteenth inch (8-1/2"x4-7/16")
mounted above passenger door.
Yes X No Exceptions
Mirror brackets shall be stainless steel and mounted to the cab and not the doors.
Yes X No Exceptions
Mirrors brackets must have eight and one half foot (8-1/2') load width.
Yes X No Exceptions
Section 29 - Lights & Electrical:
Cab and chassis wiring must be colored coded, numbered and tagged.
Yes % No Exceptions
Headlamps shall be Halogen Projector low beam/high beam complex reflector.
Yes X No Exceptions
Marker lights shall have five (5) aerodynamic mounted in.
Yes X No Exceptions
Turn signal lights shall be mounted on fender.
Yes X No Exceptions
Shall have daytime running lights.
Yes X No Exceptions
Stop/Turn/Taillights shall be Trucklite 44 LED sealed
Yes % No Exceptions
Marker lights shall have interrupter switch.
Yes No Exceptions
l
Eid Specifiicattons for one(1)new 2014 or newer Sewer Varuuin Truck
Electric backup alarm shall meet SAE J994 & OSHA
Yes X No Exceptions
Circuit breakers; replacing fuses; does not include five (5) amp circuits
Yes X No Exceptions
Shall have switch and wiring for customer installed beacon lights with thirty feet (30') additional
wire coil at back of the cab.
Yes X No Exceptions
Shall have two (2) spare switches with wiring for customer installed light package with additional
wire coil at back of the cab.
Yes X No Exceptions
Section 30 -Air Equipment:
Air Dryer shall be Bendix AD-IS heated; located per body builder instructions.
Yes No Exceptions
Moisture ejection valve with pull cable drain on each air tank.
Yes X No Exceptions
Nylon air tubing in frame and cab, excluding hoses.
Yes X No Exceptions
Air piping must be color coded.
Yes X< No Exceptions
Section 31 - Paint:
L0006EB WHITE Base coat clear coat
Yes X No Exceptions
FRAME N0001 EA BLACK
Yes X No Exceptions
Bid Spy(ificadons for one(1)new 2014 or newer Sewer Vacuum Truck
Section 32 Additional Parts
One (1) eight inch by three foot (8"x3') Higbee C/B Nozzle Assembly
Yes X No Cost
Section 33 Warranty
Unit shall have a standard factory warranty. The City of Bozeman reserves the right to do
warranty work with authorization of manufacturer. Warranty work will be billed out at eighty
dollars ($80.00) per hour straight time for warranty repairs. Prior approval will be obtained from
the manufacturer before repairs are started. All warranty parts will be shipped free of charge to
our shop with overnight designation and if parts are to be returned the manufacturer will make
arrangements to have the old parts returned at their cost. Arrangements may be made at our
approval to have warranty work done within a ten (10) mile radius of our shop. If the truck is not
operational for more than 5 days during the warranty period due to parts availability or agreed
upon repair shop's schedule, then a penalty of five hundred dollars ($500.00) per day will be
paid by the dealer who supplied the truck or an equivalent piece of equipment will be supplied
free of charge.
Yes x No Exceptions
Section 34 Service
Four hours of operator and service training to be provided at City of Bozeman Shop Complex
(814 N. Bozeman). If a model of truck is awarded the bid and that model has never been
owned by the City of Bozeman, then factory training will be provided for one mechanic. This will
be the same training provided to dealership mechanics. The training will be no less than 2 days
and no more than 5. All expenses including but not limited to travel, room and board and
classroom materials will be provided by the successful bidder. Contact the Water/Sewer Dept.
to get clarification on this before submitting bid. Failure to supply this training within one year of
delivery of truck will result in a one thousand dollar ($1000.00) penalty.
Yes No Exceptions
Section 35 Delivery
The complete units (F.O.B. City Shops Complex, 814 N. Bozeman, Bozeman, MT) shall be
delivered within two hundred forty (240 calendar days after the date of the notice to proceed.
Upon delivery of the complete unit, City of Bozeman staff will inspect the complete unit to see if
it meets bid specs. If the City staff finds that it does not meet the specs, it will be taken by the
dealer to their facility to correct the deficiencies. If the completed unit is not returned with all
deficiencies corrected within 30 days, a penalty of one hundred dollars ($100.00) per day will be
paid by the successful bidder.
Yes x No Exceptions
BID FORM
PROJECT: City of Bozeman Sewer Vacuum Truck
THIS BID SUBMITTED TO:
Bozeman City Clerk, City of Bozeman, MT, 121 N. Rouse Ave., Bozeman, MT 59715.
1. THE UNDERSIGNED BIDDER proposes and agrees that if this bid is accepted, Bidder
will enter into a Purchase Agreement with the City in the form included in the bidding
documents and will furnish the goods or product to be purchased by the City within the
number of calendar days indicated in the Agreement and in accordance with the other
terms and conditions of the bidding documents.
2. Bidder has examined, understands, accepts, and abides by all of the terms and conditions
of the Invitation to Bid, Instructions to Bidders, Bid Specifications, and Purchase
Agreement.
3. Bidder expressly covenants that if Bidder is awarded the bid, Bidder will, after the bid is
awarded and within the time specified in the Request for Bid, enter into a formal
Purchase Agreement with City. The bid must be accompanied by Bid Security payable to
the City of Bozeman for ten percent (10%) of the total amount of the bid, including
alternates, if any. The Bid Security must be in a form specified in §18-1-203, MCA,
which includes, but is not limited to, certified check, cashier's check, bank draft, bid
bond,guaranty bond,or surety bond. The Bid Security is attached hereto as Exhibit 1.
4. This bid will remain subject to acceptance for sixty (60) days after the bid opening,or for
such longer period of time that Bidder may agree to in writing upon request of City.
5. Bidder further represents that this bid is genuine and not made in the interest of or on
behalf of any undisclosed individual or entity and is not submitted in conformity with any
agreement or rules of any group, association, organization, or corporation; Bidder has not
solicited or induced any person, firm, or corporation to refrain from bidding; and Bidder
has not sought by collusion to obtain for itself any advantage over any other bidder or
over City.
6. Bidder certifies that no employee or official of the City or any member of such employee
or official's immediate family has any direct or indirect interest in the pecuniary profits
or contracts of the Bidder.
7. Bidder will provide the goods, product, or equipment being purchased by the City in
accordance with the Purchase Agreement, for the price stated on the completed Bid
Specifications sheet attached hereto as Exhibit 2.
8. Bidder understands that the unit prices shall govern in checking the bid, and should a
discrepancy exist in the total estimated price and total amount of unit prices bid as listed
Bid Form
Page 1 of 7
1
on the Bid Sheet after extensions are checked and corrections made, if any, the total
amount of unit prices bid as corrected shall be used in awarding the contract.
9. Bidder certifies that Bidder is a responsible bidder.
10. Bidder agrees that the good, product, or equipment to be purchased by City will be
delivered and ready for final payment in accordance with the Purchase Agreement.
11. If applicable, Bidder certifies receipt of City's revisions or additions made subsequent to
the advertised proposal, which are specifically acknowledged on Receipt of Addendum,
attached hereto as Exhibit 3.
12. Bidder represents that the bid is genuine and not collusive or a sham and that bidder has
not colluded, conspired, connived, or agreed, directly or indirectly, with any bidder or
person, to put in a sham bid or to refrain from bidding. Bidder further represents that
Bidder has not sought by agreement or collusion, directly or indirectly, with any person,
to fix the bid price of any other bidder, or to fix any overhead, profit, or cost element of
said bid price or that of any other bidder, or to secure any advantage against the City or
any person interested in the proposed bid. Bidder affirms that all statements in this bid
are true.
SUBMITTED on the T-day of 'Sl rne. , 20A!i—.
Bidder's Tax ID # LIS-0351%5%
IF BIDDER is:
An Individual:
(Name typed or printed)
By: (SEAL)
(Individual's Signature)
Doing business as:
Business Address:
Telephone# FAX#
A Partnership:
(Partnership Name)
By: (SEAL)
(Signature)
(Name typed or printed)
Business Address:
Telephone# FAX#
Bid Form
Page 2 of 7
2
A Corporation: �kw\ V\0'a 'r�trV (SEAL)
,� (Corporation Name)
State of Incorporation: -DeAe wo► +—
Type (General iness, Professional, Service, Limited Liability): C cof-pocnA�on
By:
(Signature of Authorized Representative)Print Name and Title: okgv\- 'e.lh&A A /�,,}s 1`loh%ee'
Attest: (Corporate Seal)
(Si natu a of Secretary)
Business Address: 1129 Odd IA ,n ' S.
'gi[Iir 5 fnT S9f 0(
Telephone# y 0G-259-SS00 FAX# q0(v-259
Date of Qualification To Do Business Is: tSV
A Joint Venture: Each Joint Venture Must Sign
Joint Venture Name: (SEAL)
(Name)
By:
(Signature of Joint Venture Partner)
Name:
(Name,printed or typed)
Title:
Business Address:
Telephone# FAX#
A Joint Venture: Each Joint Venture Must Sign
Joint Venture Name: (SEAL)
(Name)
By:
(Signature of Joint Venture Partner)
Name:
(Name,printed or typed)
Title:
Business Address:
Telephone# FAX #
Address of Joint Venture for Receipt of Official Communication:
Bid Form
Page 3 of 7
3
Address:
Telephone # FAX#
(Each Joint Venture must sign. The manner of signing for each individual, partnership and corporation that is a
party to the joint venture should be in the manner indicated above.)
Bid Form
Page 4 of 7
4
T,TAif
East Beaton Drive
We_ West Fargo,North Dakota 58078
Phone:(701)356-0130fifilACUUnERY Fax:(701)356-0139
DESIGNATION OF SIGNING AUTHORITY
I, Steven Noack, General Counsel and Secretary of Titan Machinery Inc., hereby
designate authority to Art Logan, Government Accounts Manager of Titan Machinery to enter
into and sign bid proposals, bid documents and related contracts on behalf of Titan Machinery
Inc.
Dated this 8"' day of May,2013.
TITAN MACHINERY INC.
By: Z�
Steven Noack
Its: General Counsel &Secretary
Exhibit 1
Bid Security
Attached.
Bid Form
Page 5 of 7
5