HomeMy WebLinkAbout010-G2.1-Grounding Details Docusign Envelope ID:OB8B83E5-B8B3-4B58-A2DC-E6EFCF2DDOFD STAMP:
MONOPOLE 512/2026
#6 STRANDED COPPER GROUND WIRE WITH GREEN GROUNDING TAB p N T q N
Lz
INSULATION TO SECTOR EQUIPMENT (TMA, RRU, ETC.) BOND TO TOWER GROUNDING TAB
*:' * '•
z < 4(A/S
PLATED LONG BARREL COMPRESSION LUG
z�wUSING AN EXOTHERMIC CONNECTION
ANrENNA
QUIRED) (IF TAB IS NOT PRESENT, MAKE SHELTON DOUGLAS
COAX JUMPER GROUND KIT W/ TIN PLATED EXOTHERMIC CONNECTION TO KEISLING
LONG BARREL COMPRESSION TWO HOLE LUG TOWER FLANGE BASE PLATE)
' (TYP 3 PLACES) No.PEL-PE-LIC 86951
2"x10"x1/4" THICK GROUND BAR TOWER FLANGE '. O : r
(COMMSCOPE PART# UGBKIT-0210—T 1/2"0 PVC CONDUIT (EXTEND 2'-0" BASE PLATE '•� <(/
OR APPROVED EQUIVALENT) BELOW GRADE FOR #2 SOLID TINNEDrPh O'� ' 4/CENS;�D \� '
1 (TYP) BARE COPPER GROUND WIRE)
Fz ••.......•=w C? .
° Do�Dslg�dd n�ONALENFINISHED GRADEcRo6ND BAR NNA O O O O J 01/L/gyp O O O O STATE OF MONTANA
2 ,''r) �\�/�\�/�\�/� p 4 D CGGINCHRISTOPHER GIANNOTTI EER 10 865 PE CCIVILIPLINE: C
ANTE O O \� / - A SDK SHELTON D.KEISLING 86951PE ELECTRICAL E
o SUPPORT PIPE ��\ D 0 - DJW DAVID J.WALDRON 104827PE ELECTRICAL E
D,. TMS TERRANCE M.SUPER 17412PE ELECTRICAL E
MP)
5 2'-0"
> p
LEGEND:
' MECHANICAL COMPRESSION CONNECTION NOTES:
1. ALL HARDWARE SHALL BE 18-8 STAINLESS STEEL INCLUDING BELLEVILLE
WASHERS, COAT ALL SURFACES WITH KOPR—SHIELD BEFORE MATING. BOND DIRECTLY TO TOP pOF GROUND
ROD USING EXOTHERMIC CONNECTION
= KEYED NOTES: 2. STEEL BONDING ONLY: INSERT A TOOTH WASHER BETWEEN LUG AND
STEEL, COAT ALL SURFACES WITH KOPR—SHIELD. GROUND ROD
ANTENNA PIPE GROUND KIT WIRES.1-1
z 3. USE A THIN COAT OF ANTI—CORROSION GREASE AT THESE CONNECTIONS.
a aMOUNT TOWER GROUND BAR DIRECTLY TO TOWER WITHOUT ISOLATION BUSHINGS.
CONTRACTOR TO REMOVE TOWER GALVANIZED COATING WHERE GROUND BAR 4. INSTALL WITHIN 12" OF END OF COAX TO COAX JUMPER CONNECTION.
COMES INTO CONTACT WITH TOWER. FURNISH AND INSTALL COLD GALVANIZING PLANS PREPARED FOR:
TO TOWER AND GROUND BAR CLAMPS AFTER INSTALLATION. 5. DIMPLE OR MECHANICAL CRIMP LUGS WILL NOT BE PERMITTED.
■
ANTENNA GROUNDING DIAGRAM 5 ANTENNA GROUND BAR DETAIL 3 TOWER GROUNDING DETAIL 1 verizoa
NOTES:
1. DO NOT INSTALL CABLE GROUND KIT AT A BEND AND PLANS PREPARED BY:
ALWAYS DIRECT GROUND WIRE DOWN TO GROUND BAR. --•
2. THIS DETAIL IS TYPICAL FOR EACH CABLE WHERE IT IS SPECIFIED TO BE GROUNDED. V�Iwr
3. CABLE TO BE GROUNDED AT ANTENNA LEVEL AND PRIOR HYBRID CABLE GROUND KIT W/ TIN PLATED SC
TO ENTERING EQUIPMENT CABINET. LONG BARREL COMPRESSION TWO HOLE LUG DRAWING NOTICE:
THIS DRAWING HAS NOT BEEN PUBLISHED AND IS THE SOLE
a 4. CABLE ALSO TO BE GROUNDED TO GROUND BAR AT TOWER 4"x2'-0"x1/4" THICK GROUND BAR PROPERTY OF BBC,INC.AND IS LENT TO THE BORROWER FOR
Z BASE IF APPLICABLE. (COMMSCOPE PART# UGBKIT-0424—T THEIR CONFIDENTIAL USE ONLY,AND IN CONSIDERATION OF
w THE LOAN OF THIS DRAWING,THE BORROWER PROMISES AND
OR APPROVED EQUIVALENT) MOUNT AGREES TO RETURN IT UPON REQUEST AND AGREES THAT IT
5. USE ONLY TIN PLATED GROUNDING LUGS. W/ UNISTRUT OR BRACKET TO WILL NOT BE REPRODUCED,COPIED,LENT OR OTHERWISE
TOWER O DISPOSED OF DIRECTLY OR INDIRECTLY,NOR USED FOR ANY
Iq L PURPOSE OTHER THAN FOR WHICH IT IS FURNISHED.
SUBMITTALS:
' 000 00000000000000000 DESCRIPTION DATE BY REV
0 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ADDED TOWER OPTIONS 04/04/25 AWD B
HYBRID CABLE O 0 0 0 0000000000000000 REVISED LAT LONG 10/17/25 AWD C
O REVISED PER CLIENT COMMENTS 11/20/25 JDH D
0 0 ISSUED FOR CONSTRUCTION 12/16/25 DSL 0
REVISED LAT LONG 03/18/26 DSL 1
WEATHER I I #2 SOLID TINNED COPPER GROUND WIRE REISSUED FOR CONSTRUCTION 05/08/26 CAL 2
PROOFING TO GROUND RING (TYP)
KIT APPLICANT SITE NAME:
' 2'-0" MT8 HERO-A
GROUND
STRAP KIT
NOTES: MDG LOCATION ID:
w Z SCREW ON LUG 1. ALL HARDWARE SHALL BE 18-8 STAINLESS STEEL INCLUDING BELLEVILLE 5000979700
3 ATTACHED TO
o Q WASHERS, COAT ALL SURFACES WITH KOPR—SHIELD BEFORE MATING.
GROUNDING WIRE
2. STEEL BONDING ONLY: INSERT A TOOTH WASHER BETWEEN LUG AND SITE ADDRESS:
GROUND STEEL, COAT ALL SURFACES WITH KOPR—SHIELD.
STRAP KIT 106 E OAK ST
' 3. USE A THIN COAT OF ANTI—CORROSION GREASE AT THESE CONNECTIONS. BOZEMAN,MT 59715
4. INSTALL WITHIN 12" OF END OF COAX TO COAX JUMPER CONNECTION. SHEET DESCRIPTION:-
5. DIMPLE OR MECHANICAL CRIMP LUGS WILL NOT BE PERMITTED. GROUNDING
❑m
DETAILS
a
=o COAX/HYBRID CABLE GROUND KIT DETAIL 6 TOWER/TYPICAL GROUND BAR DETAIL 4 DETAIL NOT USED 2 (2 OF 2)
U