HomeMy WebLinkAbout26 - Professional Services Agreements - Potts Drilling Inc. - Library Irrigation Wells VFD Upgrades
Professional Services Agreement for Library Irrigation Wells VFD Upgrades
Page 1 of 14
PROFESSIONAL SERVICES AGREEMENT
THIS AGREEMENT is made and entered into this 9th day of June, 2026 (“Effective Date”), by
and between the CITY OF BOZEMAN, MONTANA, a self-governing municipal corporation organized
and existing under its Charter and the laws of the State of Montana, 121 North Rouse Street,
Bozeman, Montana, with a mailing address of PO Box 1230, Bozeman, MT 59771, hereinafter
referred to as “City,” and, Potts Drilling Inc., 204 Countryside Lane, Belgrade, MT 59714, hereinafter
referred to as “Contractor.” City and Contractor may be referred to individually as “Party” and
collectively as “Parties.”
In consideration of the mutual covenants and agreements herein contained, the receipt and
sufficiency whereof being hereby acknowledged, the Parties to this Agreement agree as follows:
1. Purpose: City agrees to enter this Agreement with Contractor to perform for City
services described in the Scope of Services attached hereto as Exhibit A and by this reference made
a part hereof.
2. Term/Effective Date: This Agreement is effective upon the Effective Date and will
expire on the 1st day of June, 2027, unless earlier terminated in accordance with this Agreement.
3. Scope of Services: Contractor will perform the work and provide the services in
accordance with the requirements of the Scope of Services. For conflicts between this Agreement
and the Scope of Services, unless specifically provided otherwise, the Agreement governs.
4. Payment: City agrees to pay Contractor the amount specified in the Scope of
Services. Any alteration or deviation from the described services that involves additional costs
above the Agreement amount will be performed by Contractor after written request by City and will
become an additional charge over and above the amount listed in the Scope of Services. City must
agree in writing upon any additional charges.
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
Professional Services Agreement for Library Irrigation Wells VFD Upgrades
Page 2 of 14
5. Contractor’s Representations: To induce City to enter into this Agreement,
Contractor represents and warrants:
a. Contractor has familiarized itself with the nature and extent of this Agreement, the
Scope of Services, and with all local conditions and federal, state, and local laws, ordinances, rules,
and regulations that in any manner may affect cost, progress, or performance of the Scope of
Services.
b. Contractor has the experience and ability to perform the services required by this
Agreement.
c. Contractor will perform the services in a professional, competent, and timely manner
and with diligence and skill.
d. Contractor has the power to enter into and perform this Agreement.
e. Contractor’s performance of this Agreement must not infringe upon or violate the
rights of any third Party, whether rights of copyright, trademark, privacy, publicity, libel, slander, or
any other rights of any nature whatsoever, or violate any federal, state, and municipal laws.
Contractor agrees City will not determine or exercise control as to general procedures or
formats necessary to have these services meet this warranty.
6. Independent Contractor Status: The Parties agree that Contractor is an independent
contractor for purposes of this Agreement and is not to be considered an employee of City for any
purpose. Contractor is not subject to the terms and provisions of City’s personnel policies handbook
and is not considered a City employee for workers’ compensation or any other purpose. Contractor
is not authorized to represent City or otherwise bind City in any dealings between Contractor and
any third Parties.
Contractor must comply with the applicable requirements of the Workers’ Compensation
Act, Title 39, Chapter 71, Montana Code Annotated (MCA), and the Occupational Disease Act of
Montana, Title 39, Chapter 71, MCA. Contractor must maintain workers’ compensation coverage for
all members and employees of Contractor’s business, except for those members who are exempted
by law.
Contractor must furnish City with copies showing one of the following: (1) a binder for
workers’ compensation coverage by an insurer licensed and authorized to provide workers’
compensation insurance in the State of Montana; or (2) proof of exemption from workers’
compensation granted by law for independent contractors.
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
Professional Services Agreement for Library Irrigation Wells VFD Upgrades
Page 3 of 14
7. Prevailing Wage Requirements
a. Montana Resident Preference. The nature of the work performed, or services
provided, under this Contract meets the statutory definition of a "public works contract" in 18-2-
401, MCA. Unless superseded by federal law, Montana law requires that contractors and
subcontractors give preference to the employment of Montana residents for any public works
contract in excess of $25,000 for construction or non-construction services. Contractor must abide
by the requirements set out in 18-2-401 through 18-2-432, MCA, and all administrative rules
adopted under these statutes.
The Commissioner of the Montana Department of Labor and Industry has established the
resident requirements in accordance with 18-2-403 and 18-2-409, MCA. Any and all questions
concerning prevailing wage and Montana resident issues should be directed to the Montana
Department of Labor and Industry.
b. Standard Prevailing Rate of Wages. In addition, unless superseded by federal law, all
employees working on a public works contract must be paid prevailing wage rates in accordance
with 18-2-401 through 18-2-432, MCA, and all associated administrative rules. Montana law
requires that all public works contracts, as defined in 18-2-401, MCA, in which the total cost of the
contract is greater than $25,000, contain a provision stating for each job classification the standard
prevailing wage rate, including fringe benefits, travel, per diem, and zone pay that Contractors,
subcontractors, and employers must pay during the public works contract. Wage rate adjustments
for multiyear public works contracts are the sole responsibility of the Contractor and must be done
in accordance with 18-2-417, MCA.
c. Notice of Wages and Benefits. Furthermore, 18-2-406, MCA, requires that all
contractors, subcontractors, and employers who are performing work or providing services under a
public works contract post in a prominent and accessible site on the project staging area or work
area, no later than the first day of work and continuing for the entire duration of the contract, a
legible statement of all wages and fringe benefits to be paid to the employees in compliance with
18-2-423, MCA.
d. Wage Rates, Pay Schedule, and Records. 18-2-423, MCA, requires that employees
receiving an hourly wage must be paid on a weekly basis. Each contractor, subcontractor, and
employer must maintain payroll records in a manner readily capable of being certified for
submission under 18-2-423, MCA, for not less than three years after Contractor's, subcontractor's,
or employer's completion of work on the public works contract.
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
Professional Services Agreement for Library Irrigation Wells VFD Upgrades
Page 4 of 14
8. Labor Relations: If any labor problems or disputes arise during this Agreement,
which cause any services to cease for any period of time, Contractor agrees to take immediate steps
in its discretion, at its own expense and without expectation of reimbursement from City, to alleviate
or resolve all such labor problems or disputes. Contractor bears all costs of any related legal action.
Contractor must provide immediate relief to City so as to permit the services to continue at no
additional cost to City. Contractor acknowledges and agrees that City will not be a Party to any labor
disputes between Contractor and any subcontractors or third Parties.
9. Indemnity: For other than professional services rendered, to the fullest extent
permitted by law, Contractor agrees to release, defend, indemnify, and hold harmless the City, its
agents, representatives, employees, and officers (collectively referred to for purposes of this Section
as the City) from and against any and all claims, demands, actions, fees and costs (including
attorney’s fees and the costs and fees of expert witness and consultants), losses, expenses, liabilities
(including liability where activity is inherently or intrinsically dangerous) or damages of whatever
kind or nature connected therewith and without limit and without regard to the cause or causes
thereof or the negligence of any Party or Parties that may be asserted against, recovered from or
suffered by the City occasioned by, growing or arising out of or resulting from or in any way related
to: (i) the negligent, reckless, or intentional misconduct of Contractor; or (ii) any negligent, reckless,
or intentional misconduct of any of Contractor’s agents.
For the professional services rendered, to the fullest extent permitted by law, Contractor
agrees to indemnify and hold the City harmless against claims, demands, suits, damages, losses, and
expenses, including reasonable defense attorney fees, to the extent caused by the negligence or
intentional misconduct of Contractor or Contractor’s agents or employees.
For any labor problems or disputes or any delays or stoppages of work associated with such
problems or disputes and for any claims regarding underpaid prevailing wages, Contractor must
indemnify, defend, and hold the City harmless from any and all claims, demands, costs, expenses,
damages, and liabilities arising out of, resulting from, or occurring.
Contractor’s obligations in this Section must not be construed to negate, abridge, or reduce
other rights or obligations of indemnity that would otherwise exist. The indemnification obligations
of this Section must not be construed to negate, abridge, or reduce any common-law or statutory
rights of the City as indemnitee(s) which would otherwise exist as to such indemnitee(s).
Contractor’s indemnity under this Section must be without regard to and without any right
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
Professional Services Agreement for Library Irrigation Wells VFD Upgrades
Page 5 of 14
to contribution from any insurance maintained by City.
Should the City be required to bring an action against Contractor to assert its right to defense
or indemnification under this Agreement or under Contractor’s applicable insurance policies
required below, the City must be entitled to recover reasonable costs and attorney fees incurred in
asserting its right to indemnification or defense but only if a court of competent jurisdiction
determines Contractor was obligated to defend the claim(s) or was obligated to indemnify the City
for a claim(s) or any portion(s) thereof.
In the event of an action filed against the City resulting from the City’s performance under
this Agreement, the City may elect to represent itself and incur all costs and expenses of suit.
These obligations must survive termination of this Agreement and the services performed
hereunder.
10. Insurance: In addition to and independent from Contractor’s indemnity obligations
under Section 9, Contractor must, at Contractor’s expense, secure insurance coverage through an
insurance company or companies duly licensed and authorized to conduct insurance business in
Montana which insures the liabilities and obligations specifically assumed by Contractor in this
Section. The insurance coverage must not contain any exclusion for liabilities specifically assumed
by Contractor in Section 9.
The insurance must be occurrence-based, and cover and apply to all claims, demands, suits,
damages, losses, and expenses that may be asserted or claimed against, recovered from, or suffered
by City without limit and without regard to the cause. Contractor must furnish to City an
accompanying certificate of insurance and accompanying endorsements in amounts not less than
as follows:
• Workers’ Compensation – statutory;
• Employers’ Liability - $1,000,000 per claim; $2,000,000 per occurrence;
• Commercial General Liability - $1,000,000 per claim; $2,000,000 per occurrence;
• Automobile Liability - $1,000,000 per property damage claim and $1,000,000 per
bodily injury claim; $2,000,000 per accident; and
• Professional Liability - $1,000,000 per claim; $2,000,000 per occurrence.
The above amounts must be exclusive of defense costs. City must be endorsed as an
additional insured on a primary non-contributory basis on the Commercial General, Employer’s
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
Professional Services Agreement for Library Irrigation Wells VFD Upgrades
Page 6 of 14
Liability, and Automobile Liability policies. The insurance and required endorsements must be
approved by City and must include no less than a thirty (30) day notice of cancellation or non-
renewal. Contractor must notify City within two (2) business days of Contractor’s receipt of notice
that any required insurance coverage will be terminated or Contractor’s decision to terminate any
required insurance coverage for any reason.
City must approve all insurance coverage and endorsements prior to Contractor
commencing work. Alternative: Contractor must provide City a certificate of insurance prior to
commencing work. City must approve the limits shown on the certificate prior to commencing
work. City’s approval of the limits does not relieve Contractor of Contractor’s obligation to ensure
the insurance meets the requirements.
11. Waiver of Claims: Contractor also waives any and all claims and recourse against City,
including the right of contribution for loss or damage to person or property arising from, growing
out of, or in any way connected with or incident to the performance of this Agreement except
“responsibility for [City’s] own fraud, for willful injury to the person or property of another, or for
violation of law, whether willful or negligent” as per 28-2-702, MCA.
12. Termination for Contractor’s Fault:
a. If Contractor refuses or fails to timely do the work, or any part thereof, or fails to
perform any of its obligations under this Agreement, or otherwise breaches any terms or conditions
of this Agreement, City may, by written notice, terminate this Agreement and Contractor’s right to
proceed with all or any part of the work (“Termination Notice Due to Contractor’s Fault”). City may
then take over the work and complete it, either with its own resources or by re-letting the contract
to any other third Party.
b. In the event of a termination pursuant to this Section 12, Contractor must be entitled
to payment only for those services Contractor actually rendered.
c. Any termination provided for by this Section 12 must be in addition to any other
remedies to which City may be entitled under the law or at equity.
d. In the event of termination under this Section 12, Contractor must, under no
circumstances, be entitled to claim or recover consequential, special, punitive, lost business
opportunity, lost productivity, field office overhead, general conditions costs, or lost profits
damages of any nature arising, or claimed to have arisen, as a result of the termination.
13. Termination for City’s Convenience:
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
Professional Services Agreement for Library Irrigation Wells VFD Upgrades
Page 7 of 14
a. Should conditions arise which, in the sole opinion and discretion of City, make it
advisable to City to cease performance under this Agreement, City may terminate this Agreement
by written notice to Contractor (“Notice of Termination for City’s Convenience”). The termination
must be effective in the manner specified in the Notice of Termination for City’s Convenience and
must be without prejudice to any claims that City may otherwise have against Contractor.
b. Upon receipt of the Notice of Termination for City’s Convenience, unless otherwise
directed in the Notice, Contractor must immediately cease performance under this Agreement and
make every reasonable effort to refrain from continuing work, incurring additional expenses or costs
under this Agreement and must immediately cancel all existing orders or contracts upon terms
satisfactory to City. Contractor must do only such work as may be necessary to preserve, protect,
and maintain work already completed or immediately in progress.
c. In the event of a termination pursuant to this Section 13, Contractor is entitled to
payment only for those services Contractor actually rendered on or before the receipt of the Notice
of Termination for City’s Convenience.
d. The compensation described in Section 13(c) is the sole compensation due to
Contractor for its performance of this Agreement. Contractor must, under no circumstances, be
entitled to claim or recover consequential, special, punitive, lost business opportunity, lost
productivity, field office overhead, general conditions costs, or lost profits damages of any nature
arising, or claimed to have arisen, as a result of the termination.
14. Intellectual Property and Ownership of Work Product:
a. Title and Ownership Rights. City retains title to and all ownership rights in all Work
Product. “Work Product” includes all materials, tangible or not, created in whatever medium
pursuant to this Agreement, including but not limited to publications, promotional or educational
materials, reports, manuals, specifications, drawings and sketches, computer programs, software
and databases, schematics, marks, logos, graphic designs, notes, data and content, including but
not limited to multimedia or images (graphics, audio, and video), matters and any combinations
of, and all forms of intellectual property.
b. Ownership of Work Product. Contractor must execute any documents or take
any other actions as may reasonably be necessary, or as City may reasonably request, to
perfect City’s ownership of any Work Product. Contractor must, at no cost to City, deliver to City,
upon City request during the term of this Agreement or at its expiration or termination, a current
copy of all Work Product in the form and on the media in use as of the date of City’s request, or
such expiration or termination.
c. Return of Physical Property. Upon expiration or termination of this Agreement,
Contractor agrees to return to City all City property, including but not limited to any and all
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
Professional Services Agreement for Library Irrigation Wells VFD Upgrades
Page 8 of 14
physical items such as documentation, records, and equipment, which is in Contractor’s
possession or under Contractor’s control. Contractor must submit to City a detailed account of all
of City’s property in its possession or under Contractor’s control. Contractor must return City’s
property in a method acceptable to City within ten (10) working days. Unless otherwise mutually
agreed upon by the Parties, at no time must any of City’s property be retained by Contractor upon
expiration or termination of this Agreement.
d. Return of Data. Upon expiration or termination of this Agreement, Contractor
agrees to return to City all City data. Contractor must submit to City a detailed account of all of
City’s data in its possession or under Contractor’s control. Contractor must return City’s data in a
format acceptable to City within ten (10) working days. At no time must any data or processes that
either belong to or are intended for use of City or its officers, agents, or employees, be copied,
disclosed, or retained by Contractor upon expiration or termination of this Agreement.
e. Destruction of Data. If requested by City, Contractor agrees to destroy all of City’s
data in its possession. When requested by City to destroy City’s data, Contractor agrees to
permanently delete the data and ensure that it is not recoverable, in accordance with National
Institute of Standards and Technology (NIST) SP 800-88 “Media Sanitation Guidelines.”
f. Certification. In all cases, Contractor will certify that all of City’s information
processed during the performance of the services will be completely purged from all physical and
electronic data storage with no output to be retained by Contractor at the time the work is
completed, the Agreement is terminated, or upon written request of City.
15. Limitation on Contractor’s Damages; Time for Asserting Claim:
a. In the event of a claim for damages by Contractor under this Agreement, Contractor’s
damages must be limited to contract damages and Contractor hereby expressly waives any right to
claim or recover consequential, special, punitive, lost business opportunity, lost productivity, field
office overhead, general conditions costs, or lost profits damages of any nature or kind.
b. In the event Contractor wants to assert a claim for damages of any kind or nature,
Contractor must provide City with written notice of its claim, the facts and circumstances
surrounding and giving rise to the claim, and the total amount of damages sought by the claim,
within thirty (30) days of the facts and circumstances giving rise to the claim. In the event Contractor
fails to provide such notice, Contractor must waive all rights to assert such claim.
16. Representatives and Notices:
a. City’s Representative: City’s Representative for the purpose of this Agreement must
be Max Ziegler, Facilities Assistant Superintendent, or such other individual as City must designate
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
Professional Services Agreement for Library Irrigation Wells VFD Upgrades
Page 9 of 14
in writing. Whenever approval or authorization from or communication or submission to City is
required by this Agreement, such communication or submission must be directed to City’s
Representative and approvals or authorizations must be issued only by such Representative;
provided, however, that in exigent circumstances when City’s Representative is not available,
Contractor may direct its communication or submission to other designated City personnel or agents
as designated by City in writing and may receive approvals or authorization from such persons.
b. Contractor’s Representative: Contractor’s Representative for the purpose of this
Agreement must be Dave Potts, or such other individual as Contractor must designate in writing.
Whenever direction to or communication with Contractor is required by this Agreement, such
direction or communication must be directed to Contractor’s Representative; provided, however,
that in exigent circumstances when Contractor’s Representative is not available, City may direct its
direction or communication to other designated Contractor personnel or agents.
c. Notices: All notices required by this Agreement must be in writing and must be
provided to the Representatives named in this Section. Notices must be deemed given when
delivered, if delivered by courier to Party’s address shown above during normal business hours of
the recipient; or when sent, if sent by email or fax (with a successful transmission report) to the
email address or fax number provided by the Party’s Representative; or on the fifth business day
following mailing, if mailed by ordinary mail to the address shown above, postage prepaid.
17. Permits: Contractor must provide all notices, comply with all applicable laws,
ordinances, rules, and regulations, obtain all necessary permits, licenses, including a City of Bozeman
business license, and inspections from applicable governmental authorities, and pay all fees and
charges in connection therewith.
18. Laws and Regulations: Contractor must comply fully with all applicable state and
federal laws, regulations, and municipal ordinances including, but not limited to, all workers’
compensation laws, all environmental laws including, but not limited to, the generation and disposal
of hazardous waste, the Occupational Safety and Health Act (OSHA), the safety rules, codes, and
provisions of the Montana Safety Act in Title 50, Chapter 71, MCA, all applicable City, County, and
State building and electrical codes, the Americans with Disabilities Act, and all non-discrimination,
affirmative action, and utilization of minority and small business statutes and regulations.
20. Generative Artificial Intelligence (AI): Contractor must inform the City’s
representative of its intention to utilize Generative AI to fulfill the deliverables or services detailed
in the Scope of Services. City’s representative may, in their discretion, permit or deny Contractor’s
use of Generative AI. If Contractor is permitted to use Generative AI, Contractor agrees to review
any work created by Generative AI for accuracy, bias, and copyright infringement. Contractor agrees
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
Professional Services Agreement for Library Irrigation Wells VFD Upgrades
Page 10 of 14
it will never submit any confidential or personal identifiable information acquired through this
Agreement into a Generative AI system. For the purposes of this section, Generative AI is defined as
a deep learning model that can generate high quality content such as stories or writings, images,
voice replication and music.
21. Nondiscrimination and Equal Pay: Contractor agrees that all hiring by Contractor of
persons performing this Agreement must be on the basis of merit and qualifications. Contractor
must have a policy to provide equal employment opportunity in accordance with all applicable state
and federal anti-discrimination laws, regulations, and contracts. Contractor cannot refuse
employment to a person, bar a person from employment, or discriminate against a person in
compensation or in a term, condition, or privilege of employment because of race, color, religion,
creed, political ideas, sex, age, marital status, national origin, actual or perceived sexual orientation,
gender identity, physical or mental disability, except when the reasonable demands of the position
require an age, physical or mental disability, marital status or sex distinction. Contractor is subject
to and must comply with Title VI of the Civil Rights Act of 1964; Section 140, Title 2, United States
Code, and all regulations promulgated thereunder.
Contractor represents it is, and for the term of this Agreement will be, in compliance with
the requirements of the Equal Pay Act of 1963 and Section 39-3-104, MCA (the Montana Equal Pay
Act). Contractor must report to City any violations of the Montana Equal Pay Act that Contractor has
been found guilty of within 60 days of such finding for violations occurring during the term of this
Agreement.
Contractor must require these nondiscrimination terms of its subcontractors providing
services under this Agreement.
22. Intoxicants; DOT Drug and Alcohol Regulations/Safety and Training: Contractor
must not permit or suffer the introduction or use of any intoxicants, including alcohol or illegal drugs,
by any employee or agent engaged in services to City under this Agreement while on City property
or in the performance of any activities under this Agreement. Contractor acknowledges it is aware
of and must comply with its responsibilities and obligations under the U.S. Department of
Transportation (DOT) regulations governing anti-drug and alcohol misuse prevention plans and
related testing. City must have the right to request proof of such compliance and Contractor must
be obligated to furnish such proof.
Contractor must be responsible for instructing and training Contractor's employees and
agents in proper and specified work methods and procedures. Contractor must provide continuous
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
Professional Services Agreement for Library Irrigation Wells VFD Upgrades
Page 11 of 14
inspection and supervision of the work performed. Contractor is responsible for instructing its
employees and agents in safe work practices.
23. Modification and Assignability: This Agreement may not be enlarged, modified or
altered except by written agreement signed by both Parties. Contractor may not subcontract or
assign Contractor’s rights, including the right to compensation or duties arising hereunder, without
the prior written consent of City. Any subcontractor or assignee will be bound by all of the terms
and conditions of this Agreement.
24. Reports/Accountability/Public Information: Contractor agrees to develop and/or
provide documentation as requested by City demonstrating Contractor’s compliance with the
requirements of this Agreement. Contractor must allow City, its auditors, and other persons
authorized by City to inspect and copy its books and records for the purpose of verifying that the
reimbursement of monies distributed to Contractor pursuant to this Agreement was used in
compliance with this Agreement and all applicable provisions of federal, state, and local law.
Contractor cannot issue any statements, releases or information for public dissemination without
prior approval of City.
25. Non-Waiver: A waiver by either Party of any default or breach by the other Party of
any terms or conditions of this Agreement does not limit the other Party’s right to enforce such term
or conditions or to pursue any available legal or equitable rights in the event of any subsequent
default or breach.
26. Attorney’s Fees and Costs: In the event it becomes necessary for either Party to
retain an attorney to enforce any of the terms or conditions of this Agreement or to give any notice
required in this Agreement, the prevailing Party or the Party giving notice is entitled to reasonable
attorney's fees and costs, including fees, salary, and costs of in-house counsel including the City
Attorney’s Office staff.
27. Taxes: Contractor is obligated to pay all taxes of any kind or nature and make all
appropriate employee withholdings.
28. Dispute Resolution:
a. Any claim, controversy, or dispute between the Parties, their agents, employees, or
representatives must be resolved first by negotiation between senior-level personnel from each
Party duly authorized to negotiate settlement agreements. Upon mutual agreement of the Parties,
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
Professional Services Agreement for Library Irrigation Wells VFD Upgrades
Page 12 of 14
the Parties may invite an independent, disinterested mediator to assist in the negotiated settlement
discussions. The Parties must attempt to resolve by negotiation within 90 days after the claim,
controversy, or dispute has arisen.
b. If the Parties are unable to resolve the dispute pursuant to subsection (a), then such
dispute may only be resolved in a court of competent jurisdiction in compliance with the Applicable
Law provisions of this Agreement. In such a case, all court actions must be commenced within 1 year
after the settlement procedure in subsection (a) has been exhausted.
29. Survival: Contractor’s indemnification must survive the termination or expiration of
this Agreement for the maximum period allowed under applicable law.
30. Headings: The headings used in this Agreement are for convenience only and are not
to be construed as a part of the Agreement or as a limitation on the scope of the particular
paragraphs to which they refer.
31. Severability: If any portion of this Agreement is held to be void or unenforceable, all
other provisions of this Agreement must remain in effect.
32. Applicable Law: The Parties agree that this Agreement is governed by the laws of the
State of Montana.
33. Binding Effect: This Agreement is binding upon and inures to the benefit of the heirs,
legal representatives, successors, and assigns of the Parties.
34. No Third-Party Beneficiary: This Agreement is for the exclusive benefit of the Parties,
does not constitute a third-Party beneficiary agreement, and may not be relied upon or enforced by
a third Party.
35. Counterparts: This Agreement may be executed in counterparts, which together
constitute this Agreement.
36. Integration: This Agreement and all Exhibits attached hereto constitute the entire
Agreement of the Parties. Covenants or representations not contained herein or made a part
thereof by reference, are not binding upon the Parties. There are no understandings between the
Parties other than as set forth in this Agreement. All communications, either oral or written, made
prior to the date of this Agreement are hereby abrogated and withdrawn unless specifically made a
part of this Agreement by reference.
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
Professional Services Agreement for Library Irrigation Wells VFD Upgrades
Page 13 of 14
37. Consent to Electronic Signatures: The Parties have consented to execute this
Agreement electronically in conformance with the Montana Uniform Electronic Transactions Act,
Title 30, Chapter 18, Part 1, MCA.
38. Extensions: This Agreement may, upon mutual agreement, be extended for a period
of up to one year at a time by written agreement of the Parties. In no case, however, may this
Agreement run longer than five (5) years from the effective date of this Agreement.
**** END OF AGREEMENT EXCEPT FOR SIGNATURES ****
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
Professional Services Agreement for Library Irrigation Wells VFD Upgrades
Page 14 of 14
IN WITNESS WHEREOF, the Parties hereto have executed this Agreement the day and year
first above written or as recorded in an electronic signature.
CITY OF BOZEMAN, MONTANA POTTS DRILLING INC.
CONTRACTOR (Type Name Above)
By________________________________ By__________________________________
Chuck Winn, City Manager
Print Name: ___________________________
Print Title: ____________________________
APPROVED AS TO FORM:
By_______________________________
Greg Sullivan, Bozeman City Attorney
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
President
Ben Minden
EXHIBIT A
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
WWWWWWWWWWWWWWWWWWWWWWWWWWWWWWYHDYHDYHD
YHDWWWWWWWWWWWWWWWWWW
RAMPRAMPRAMPRAMPRAMP
RAMP RAMPRAMPLANDING
RAMP RAMPRAMPLANDINGLANDING
LANDINGLANDINGRAMPGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGWSWSWWSFWSGGGGGGGGGGGGGG2" GASGG4" GAS4" GASG4" GASGGG4" GASGGGGGGGGGG G GGGGGGGGGGGG 4799
4798
4797
4797
4797
4798
47
9
7
4
7
9
8
47
9
848014803
48
0
448064808
48074806
480
5
4802
4800
4793
4792
4791
479
7WWWWWWWBHCTM
DRAWN BYAPPROVEDDATEREVISIONSIRRIGATION SCOPE EXHIBIT SCALE: 1" = 80'NEIL RYANKINER232MNOTNAAOFT
ET
A
S
EEPACSDNALTCETI
HCRAENSEDLICSNCNRKCOVER251035BOZEMAN PUBLIC LIBRARY IRRIGATION RENOVATION
626 E MAIN STREET
BOZEMAN, MT 59715
COVER SHEET LANDSCAPE ARCHITECTURE & PLANNING
(406) 850-0461 www.secondnature.consultingFOR CONSTRUCTION05-14-2026EXISTING WELLWELL #2EXISTING WELLWELL #1BOZEMANPUBLICLIBRARYMAIN STREETSOUTH WALLACE AVEPROJECT SITE626 EAST MAIN STREETBOZEMAN, MT 59715AREA MAP NTSIRRIGATION IMPROVEMENTSBOZEMANPUBLICLIBRARYLANDSCAPE ARCHITECT:SECOND NATURE CONSULTINGATTN: Neil Kiner, PLA, ASLA2722 3rd Ave North, Suite 230Billings, Montana 59101SHEET SET:COVER SHEETL0.1SCOPE EXHIBIT, NOTESL1.1 - IRRIGATION PLANL1.2 - IRRIGATION PLANL1.3 - IRRIGATION PLANL2.1 - IRRIGATION DETAILSL2.2 - IRRIGATION DETAILSCITY OF BOZEMAN:FACILITIES DEPARTMENTATTN: Max ZieglerFacilities Assistant Superintendent20 E. Olive Street, Office 014BBozeman, MT 59715Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
WWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWYHD YHD YHDYHD W WWWWWWWWWWWWWWWWW WW W W W W W W W
W W W W
RAMPRAMPRAMPRAMPRAMP
RAMP
RAMP
RAMPLANDING
RAMPRAMPRAMPLANDINGLANDINGLANDINGLANDINGRAMPGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGWSWSWSWSWWSFWSWSGGGGGGGGGGGGGGGGGGGGG G G G 2" GASGGG4" GAS4" GASGG4" GASG4" GASGGGGGGGGGGGGGGGGGGGGGGGGGGGGG 47994798479747974797479847974798479848014803480448064805480248004793479247914797WWWWBHCT M WWWWBOZEMANPUBLICLIBRARYDRAWN BYAPPROVEDDATEREVISIONSSCOPE EXHIBIT SCALE: 1" = 50'0050'100'SCALE IN FEETNEIL RYANKINER232MNOTNAAOFT
ET
A
S
EEPACSDNALTCETI
HCRAENSEDLICSNCNRKL0.1251035BOZEMAN PUBLIC LIBRARY IRRIGATION RENOVATION
626 E MAIN STREET
BOZEMAN, MT 59715
IRRIGATION SCOPE EXHIBIT LANDSCAPE ARCHITECTURE & PLANNING
(406) 850-0461 www.secondnature.consultingIRRIGATION RENOVATION LEGENDNEW DRIPIRRIGATIONNEW TURF GRASSIRRIGATIONNO NEW DRIP IRRIGATION(ABANDON EXISTING)NATURALIZED AREAS -NO NEW IRRIGATION(ABANDON EXISTING)FOR CONSTRUCTION05-14-2026LOCATION OF WELL #2LOCATION OF WELL #1THIS SITE IS SERVED WITH TWO EXISTING IRRIGATION WELLS. EACHWELL IS TO BE UPGRADED WITH THE SAME EQUIPMENT LISTED BELOW.THREE PHASE MOTORCENTRIPRO M304323 HP, 230vSUBMERSIBLE PUMPGOULDS 35GS30PRESSURE TANK MANIFOLDBOSHART INDUSTRIES, 07M-200SSQUICK COUPLER VALVERAINBIRD 5-LRCVALVE BOXNDS 17" X 30" PRO-SPECVARIABLE FREQUENCY DRIVEAQUAVAR SOLO2 3AS30PRESSURE TANKWELL X TROL BY AMTROL, WX-102IRRIGATION WELL EQUIPMENT SCHEDULEIRRIGATION NOTES:1.SCOPE OF WORK OF THIS PROJECT WILL INCLUDE THE RENOVATION OF THE IRRIGATION SYSTEM AT THE CITY OFBOZEMAN PUBLIC LIBRARY. CONTRACTOR IS RESPONSIBLE FOR REMOVAL OF EXISTING COMPONENTS AND INSTALLATIONOF NEW COMPONENTS.1.1.CONTRACTOR TO REMOVE ALL VALVE BOXES, VALVES, WIRING ASSEMBLIES, AND IRRIGATION HEADS.1.1.1.VALVE BOXES SHALL BE BACKFILLED WITH APPROVED OFF-SITE PLANTING SOIL.1.1.2.BELOW GRADE LATERAL LINES AND MAIN LINES WILL BE ALLOWED TO BE LEFT IN PLACE. ALL HEADS SHALL BEREMOVED FROM LATERAL LINES. ALL LINES SHALL BE REMOVED FROM SLEEVES.2.CONTRACTOR TO VERIFY EXISTING CONDITIONS. ALL EXISTING UTILITIES ARE TO BE LOCATED BEFORE TRENCHING OFANY KIND BEGINS.3.PROTECT ALL EXISTING IMPROVEMENTS TO REMAIN. IF DAMAGE OCCURS RESULTANT FROM CONTRACTOR'S OPERATIONSOR NEGLIGENCE, REPAIR BACK TO ORIGINAL CONDITION AT CONTRACTOR'S EXPENSE.4.COORDINATE ALL WORK WITH CITY OF BOZEMAN FACILITIES DEPARTMENT. ENSURE THAT PUBLIC ACCESS TO LIBRARY ISMAINTAINED THROUGHOUT DURATION OF CONSTRUCTION.5.INSTALL IRRIGATION SYSTEM AS DETAILED AND PER MANUFACTURER'S SPECIFICATIONS.6.IRRIGATION PIPING LAYOUT IS SCHEMATIC. ACTUAL LOCATION OF PIPING AND OTHER COMPONENTS MAY VARY DUE TOEXISTING SITE CONDITIONS. PLACEMENT OF PIPE AND HEADS SHALL BE FIELD ADJUSTED TO ACCOMMODATE ACTUAL SITECONDITIONS.7.ALL MAINLINE SHALL BE AT LEAST 18" BELOW FINISHED GRADE. ALL LATERAL LINES SHALL BE AT LEAST 12" BELOWFINISHED GRADE.8.CONTRACTOR TO UTILIZE EXISTING UNDER PAVEMENT SLEEVING. LOCATION OF SLEEVES ARE UNKNOWN. PAVEMENTCUTTING AND PATCHING SHOULD ONLY BE USED AS A WORST CASE OPTION. COORDINATE ALL DISRUPTIONS TO PARKINGLOT OR ANY OTHER PAVED SURFACE WITH FACILITIES DEPARTMENT AND LIBRARY MANAGEMENT.9.RE-GRADE AND REPAIR ALL EXISTING AREAS DISTURBED BY CONTRACTOR'S OPERATIONS. A DISTURBED AREA SHALL BEWHERE CONSTRUCTION ACTIVITIES INCLUDING TRENCHING, DEMOLITION, EARTHWORK, MATERIAL STORAGE, STAGING,PARKING, OR ANY OTHER FORM OF EXCAVATION, COMPACTION, OR TRAFFIC RESULTS IN THE REMOVAL OR DISPLACEMENTOF EXISTING GROUND COVER OR GRADE. COORDINATE WITH GENERAL CONTRACTOR.10.SYSTEM DESIGN IS BASED ON CONNECTION TO (2) EXISTING IRRIGATION WELLS. EACH WELL SHALL BE UPGRADED WITHNEW SUBMERSIBLE WELL AND MOTOR, PRESSURE TANK ASSEMBLY, AND CONTROLS.11.PROVIDE ALL COMPONENTS REQUIRED TO COMPLETELY WINTERIZE THE IRRIGATION SYSTEM WHETHER OR NOTSPECIFIED HEREIN.12.PROVIDE TEMPORARY WATERING AS NECESSARY. 13. PROVIDE POWER TO IRRIGATION CONTROLLER AND WELL CONTROLS AS NEEDED. COORDINATE POWER SOURCE WITHLICENSED ELECTRICIAN.14.INSTALL 2-WIRE CONTROL WIRES FROM ELECTRIC VALVES TO CONTROLLER, INCLUDING DECODERS AS NEEDED.15.IF NEW SLEEVES ARE NEEDED, PROVIDED SLEEVES SHALL BE (2) SIZES LARGER THAN PIPE OR COMBINATION OF PIPESTHEREIN ENCLOSED, WITH MINIMUM SIZE TO BE 4" (2" FOR CONTROL WIRES). SUPPLY (1) EXTRA SLEEVE. INSTALL 24" BELOWFINISHED GRADE AND EXTEND SLEEVES 12" PAST CURBS. TAPE/PLUG AND MARK ALL SLEEVE ENDS PRIOR TO BACKFILL.16.CONTRACTOR TO ADJUST IRRIGATION DISTRIBUTION TO PROVIDE COMPLETE COVERAGE AND TO MINIMIZE WASTEWATER.17.ALL PRESSURIZED MAIN LINE AND FITTINGS ABOVE GRADE SHALL BE GALVANIZED STEEL.18.IRRIGATION CONTRACTOR TO PROVIDE PRESSURE TEST RESULTS OF MAINLINE CONNECTIONS TO GENERALCONTRACTOR PRIOR TO BACKFILLING.19.IN PARKING LOT LANDSCAPING, CITY OF BOZEMAN MAY PROVIDE NEW LANDSCAPE PLANTINGS. ALL NEW PLANTS SHALLBE SERVED WITH NEW DRIP IRRIGATION. CONTRACTOR TO SUPPLY A MINIMUM OF (2) DRIP EMITTERS PER PLANT.PERENNIALS = 2 EMITTERS, SHRUBS = 3 EMITTERS. CONTRACTOR MAY UTILIZE MULTI-PORT EMITTERS IN LANDSCAPE BEDSWHERE APPROPRIATE.20.INSTALL ALL COMPONENTS PER MANUFACTURER'S INSTRUCTIONS.21.CONTRACTOR TO RECORD ALL AS-BUILT CONDITIONS. SEE PROJECT MANUAL FOR SUBMITTAL REQUIREMENTS FOR ASBUILT DRAWINGS.22.CONTRACTOR TO CONTACT RAINBIRD REPRESENTATIVE: DREW BARBER, (970) 846-7163.Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
YHDWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWW WW W W WW WW W W WW W W W W W W W W W W W W W W W W
47994801480348044806480548024800WWWW WW28282828303028282828282218 1212141414161616161616182022242824242424222222222222222222222222222222
2624222226202026242624242412
1010
10
1012
14
14
14
12
10882424242426262628242426242424242424181818181822242424242222222222222222
20222224242422222222222222222222222222222222222222222222222222222222222222222230WELL #1 (A)1"1"112"112"1"1"112"14
1210
8814 141210
10
10
10
12
1"1"112"1A20.01"1A2A18.91"2A3A29.11"3A4A29.01"4A5A23.51"5A1B25.31"1B2B25.71"2B3B25.21"3B4B30.91"4B5B17.51"5B6B12.81"6B7B22.81"7B8B16.81"8B1"112"1"112"1"1"112"1"1"112"1"1"112"1"112"1"1"112"1"1"112"112"1"1"1"112"1"112"1"1"112"1"112"1"1"1"112"1"1"1"1"112"1"1"1"112"1"1"1"1"112"1"1"112"1"1"112"LXFDFDFDFDFDSYMBOLMANUFACTURER/MODEL/DESCRIPTIONHUNTER MP STRIP RB 1806-SAM-P45TURF ROTATOR, 6IN. POP-UP WITH CHECK VALVE,PRESSURE REGULATED TO 45 PSI, MP ROTATOR NOZZLEON RB 1806 BODY.HUNTER MP1000 RB 1806-SAM-P45TURF ROTATOR, 6IN. POP-UP WITH CHECK VALVE,PRESSURE REGULATED TO 45 PSI, MP ROTATOR NOZZLEON RB 1806 BODY.HUNTER MP2000 RB 1806-SAM-P45TURF ROTATOR, 6IN. POP-UP WITH CHECK VALVE,PRESSURE REGULATED TO 45 PSI, MP ROTATOR NOZZLEON RB 1806 BODY.HUNTER MP3000 RB 1806-SAM-P45TURF ROTATOR, 6IN. POP-UP WITH CHECK VALVE,PRESSURE REGULATED TO 45 PSI, MP ROTATOR NOZZLEON RB 1806 BODY.HUNTER MP3500 RB 1806-SAM-P45TURF ROTATOR, 6IN. POP-UP WITH CHECK VALVE,PRESSURE REGULATED TO 45 PSI, MP ROTATOR NOZZLEON RB 1806 BODY.SYMBOLMANUFACTURER/MODEL/DESCRIPTIONRAIN BIRD XCZ-100-LC 1"WIDE FLOW DRIP CONTROL KIT, FOR COMMERCIAL USES.1IN. PESB VALVE, WITH 1IN. PRESSURE REGULATING 40PSIBASKET FILTER. 0.3-20 GPM.RAIN BIRD XCZ-150-LCDR 1-1/2"HIGH FLOW CONTROL ZONE KIT, FOR LARGE COMMERCIALDRIP ZONES. 1-1/2IN. PESB-R SCRUBBER GLOBE VALVEWITH HIGH-CAPACITY FILTER AND PRESSURE REGULATINGSYSTEM (PRS) FIXED AT 40PSI. FLOW RANGE: 20 - 62 GPM.AREA TO RECEIVE DRIPLINERAIN BIRD XFCV-06-12XFCV XON-SURFACE LANDSCAPE DRIPLINE WITH AHEAVY-DUTY 3.5 PSI CHECK VALVE. 0.6 GPH EMITTERS AT12" O.C. DRIPLINE LATERALS SPACED AT 12" APART, WITHEMITTERS OFFSET FOR TRIANGULAR PATTERN. GREATFOR ELEVATION CHANGE. SPECIFY XF INSERT FITTINGS.SYMBOLMANUFACTURER/MODEL/DESCRIPTIONRAIN BIRD PESB 1"1IN., 1-1/2IN., 2IN., 3IN., 3IN. PLASTIC INDUSTRIAL REMOTECONTROL VALVE. LOW FLOW OPERATING CAPABILITY,GLOBE CONFIGURATION. WITH SCRUBBER TECHNOLOGYFOR RELIABLE PERFORMANCE IN DIRTY WATERIRRIGATION APPLICATIONS.RAIN BIRD 5-RC 1"1IN. BRASS QUICK-COUPLING VALVE, WITHCORROSION-RESISTANT STAINLESS STEEL SPRING,THERMOPLASTIC RUBBER COVER, AND 1-PIECE BODY.APOLLO VALVES 94ALF10801BALL VALVE, INLET SIZE 2IN., LEAD FREE BRASS BODY,FULL-PORT, BLOW-OUT PROOF STEM DESIGNRAIN BIRD ESP-LXD-LXMMPED50 STATION, 2-WIRE DECODER BASED CONTROLLER INPOWDER COATED METAL, CABINET W/ PEDESTAL. (1)ESP-LXD 50-STATION, INDOOR/OUTDOOR, PLASTICWALL-MOUNT ENCLOSURE. INSTALL IN RAIN BIRDLXMM-LXMMPED POWDER COATED METAL CABINET W/PEDESTAL. SYSTEM REQUIREMENTS: RAIN BIRDFD-XXX-TURF FIELD DECODERS, PAIGE ELECTRIC CABLEP7072D & RAIN BIRD WC20 DRY SPLICES ONLY. GROUNDSYSTEM W/ (X) LSP-1TURF LINE SURGE PROTECTORS INRAIN BIRD ROUND VALVE BOXES. INSTALL PERMANUFACTURERS RECOMMENDATIONS.RAIN BIRD FD-X0XTURFFIELD DECODER FOR TWO-WIRE SYSTEM. INSTALL INVALVE BOX FOR VALVE. FD 101/102/202/401/601VALVE/SOLENOIDS. USE LINE SURGE PROTECTION ASPER MANUFACTURERFT.S DIRECTIONS.RAIN BIRD IQ4G-USAIQ NCC 4G CELLULAR CARTRIDGE UPGRADES ESP-LXSERIES CONTROLLERS TO IQ SATELLITE, FORCOMMUNICATION WITH IQ CENTRAL CONTROL. INCLUDEIQEXTANT4G EXTERNAL ANTENNA FOR METAL ORSTAINLESS STEEL CABINET/PEDESTAL. USED FOR DIRECTOR SERVER SATELLITE APPLICATIONS.RAIN BIRD LXIVMOUTFIELD DEVICE TO INTERFACE BETWEEN 3RD PARTYVALVES OR PUMP START RELAY & ESPLXIVM(P), 2-WIRECONTROLLERS. (1) LXIVMOUT PER VALVE/RELAY (DCLATCHING SOLENOID REQUIRED).POINT OF CONNECTION 2"EXISTING WELL #1POINT OF CONNECTION 2"EXISTING WELL #2IRRIGATION LATERAL LINE: PVC SCHEDULE 40IRRIGATION MAINLINE: PVC SCHEDULE 40 2"PIPE SLEEVE: PVC SCHEDULE 40LOCATE & USE EXISTING SLEEVESLSTRSTSST1000200030003500CFDIQLXWELL #1 (A)WELL #2 (B)Valve NumberValve FlowValve SizeValve Callout###"IRRIGATION SCHEDULENEIL RYANKINER232MNOTNAAOFT
ET
A
S
EEPACSDNALTCETI
HCRAENSEDLICSNCNRKL1.1251035BOZEMAN PUBLIC LIBRARY IRRIGATION RENOVATION
626 E MAIN STREET
BOZEMAN, MT 59715
IRRIGATION PLAN LANDSCAPE ARCHITECTURE & PLANNING
(406) 850-0461 www.secondnature.consultingDRAWN BYAPPROVEDDATEREVISIONSIRRIGATION PLAN SCALE: 1" = 20'0020'40'SCALE IN FEETFOR CONSTRUCTION
SEE SHEET L1.2 MAINTENANCE ,EDGE, TYP.05-14-2026NUMBERMODELSIZETYPEGPMWIREPSIPSI @ POCPRECIP1ARAIN BIRD PESB1"TURF ROTARY19.97164.044.546.20.36 in/h1BRAIN BIRD PESB1"TURF ROTARY25.33420.947.049.10.35 in/h2ARAIN BIRD PESB1"TURF ROTARY18.95158.044.245.70.33 in/h2BRAIN BIRD PESB1"TURF ROTARY25.65414.846.348.30.37 in/h3ARAIN BIRD PESB1"TURF ROTARY29.11152.046.650.10.41 in/h3BRAIN BIRD PESB1"TURF ROTARY25.17408.845.547.50.36 in/h4ARAIN BIRD PESB1"TURF ROTARY29.05106.746.751.30.41 in/h4BRAIN BIRD PESB1"TURF ROTARY30.87265.847.749.40.37 in/h5ARAIN BIRD PESB1"TURF ROTARY23.47112.744.948.00.41 in/h5BRAIN BIRD PESB1"TURF ROTARY17.54108.843.643.70.3 in/h6ARAIN BIRD XCZ-150-LCDR1-1/2"AREA FOR DRIPLINE20.99471.238.242.21.18 in/h6BRAIN BIRD PESB1"TURF ROTARY12.84102.844.544.60.39 in/h7ARAIN BIRD XCZ-150-LCDR1-1/2"AREA FOR DRIPLINE20.82477.241.345.31.18 in/h7BRAIN BIRD PESB1"TURF ROTARY22.8396.845.045.10.36 in/h8ARAIN BIRD PESB1"TURF ROTARY20.15687.844.548.40.37 in/h8BRAIN BIRD PESB1"TURF ROTARY16.8496.843.243.30.46 in/h9ARAIN BIRD PESB1"TURF ROTARY11.69693.842.543.90.32 in/h9BRAIN BIRD PESB1"TURF ROTARY17.8584.143.944.10.33 in/h10ARAIN BIRD XCZ-150-LCDR1-1/2"AREA FOR DRIPLINE30.33933.937.347.51.12 in/h10BRAIN BIRD XCZ-150-LCDR1-1/2"AREA FOR DRIPLINE28.47117.138.338.91.25 in/h11ARAIN BIRD PESB1"TURF ROTARY19.28939.944.949.40.29 in/h11BRAIN BIRD XCZ-150-LCDR1-1/2"AREA FOR DRIPLINE31.16207.738.740.21.29 in/h12ARAIN BIRD PESB1"TURF ROTARY20.73945.945.750.80.31 in/h12BRAIN BIRD PESB1"TURF ROTARY23.04227.646.547.40.49 in/h13ARAIN BIRD XCZ-150-LCDR1-1/2"AREA FOR DRIPLINE33.91951.938.351.11.24 in/h13BRAIN BIRD PESB1"TURF ROTARY16.81233.644.244.70.32 in/h14BRAIN BIRD XCZ-100-LC1"AREA FOR DRIPLINE3.31477.037.938.01.28 in/h15BRAIN BIRD PESB1"TURF ROTARY16.75483.044.946.10.38 in/hCommon Wire1,920VALVE SCHEDULEMAINTENANCE ,EDGE, TYP.Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
WWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWYHDWYHDWWWWW W W W W W W W W W W W
RAMPRAMPRAMPRAMPLANDINGLANDINGRAMP 479847974797479747984797479847984797BH CTM W WW20181822222222222020242222222222223020202020202020202020202030303030303030303030303030303232323232262420222414261"1"2020181616161618
208B16.89B9B17.81"12B23.01"12B13B16.81"13B14B3.311"14B15B16.71"15B1"1"1"1"1"112"1"1"1"112"1"1"1"112"1"112"1"1"1"112"1"1"1"112"2"11B31.2112"11B1"1"1"112"1"1"1"6A21.0112"6A7A20.8112"7A10B28.5112"10BLXFDFDFDFDWELL #2 (B)IQCSYMBOLMANUFACTURER/MODEL/DESCRIPTIONHUNTER MP STRIP RB 1806-SAM-P45TURF ROTATOR, 6IN. POP-UP WITH CHECK VALVE,PRESSURE REGULATED TO 45 PSI, MP ROTATOR NOZZLEON RB 1806 BODY.HUNTER MP1000 RB 1806-SAM-P45TURF ROTATOR, 6IN. POP-UP WITH CHECK VALVE,PRESSURE REGULATED TO 45 PSI, MP ROTATOR NOZZLEON RB 1806 BODY.HUNTER MP2000 RB 1806-SAM-P45TURF ROTATOR, 6IN. POP-UP WITH CHECK VALVE,PRESSURE REGULATED TO 45 PSI, MP ROTATOR NOZZLEON RB 1806 BODY.HUNTER MP3000 RB 1806-SAM-P45TURF ROTATOR, 6IN. POP-UP WITH CHECK VALVE,PRESSURE REGULATED TO 45 PSI, MP ROTATOR NOZZLEON RB 1806 BODY.HUNTER MP3500 RB 1806-SAM-P45TURF ROTATOR, 6IN. POP-UP WITH CHECK VALVE,PRESSURE REGULATED TO 45 PSI, MP ROTATOR NOZZLEON RB 1806 BODY.SYMBOLMANUFACTURER/MODEL/DESCRIPTIONRAIN BIRD XCZ-100-LC 1"WIDE FLOW DRIP CONTROL KIT, FOR COMMERCIAL USES.1IN. PESB VALVE, WITH 1IN. PRESSURE REGULATING 40PSIBASKET FILTER. 0.3-20 GPM.RAIN BIRD XCZ-150-LCDR 1-1/2"HIGH FLOW CONTROL ZONE KIT, FOR LARGE COMMERCIALDRIP ZONES. 1-1/2IN. PESB-R SCRUBBER GLOBE VALVEWITH HIGH-CAPACITY FILTER AND PRESSURE REGULATINGSYSTEM (PRS) FIXED AT 40PSI. FLOW RANGE: 20 - 62 GPM.AREA TO RECEIVE DRIPLINERAIN BIRD XFCV-06-12XFCV XON-SURFACE LANDSCAPE DRIPLINE WITH AHEAVY-DUTY 3.5 PSI CHECK VALVE. 0.6 GPH EMITTERS AT12" O.C. DRIPLINE LATERALS SPACED AT 12" APART, WITHEMITTERS OFFSET FOR TRIANGULAR PATTERN. GREATFOR ELEVATION CHANGE. SPECIFY XF INSERT FITTINGS.SYMBOLMANUFACTURER/MODEL/DESCRIPTIONRAIN BIRD PESB 1"1IN., 1-1/2IN., 2IN., 3IN., 3IN. PLASTIC INDUSTRIAL REMOTECONTROL VALVE. LOW FLOW OPERATING CAPABILITY,GLOBE CONFIGURATION. WITH SCRUBBER TECHNOLOGYFOR RELIABLE PERFORMANCE IN DIRTY WATERIRRIGATION APPLICATIONS.RAIN BIRD 5-RC 1"1IN. BRASS QUICK-COUPLING VALVE, WITHCORROSION-RESISTANT STAINLESS STEEL SPRING,THERMOPLASTIC RUBBER COVER, AND 1-PIECE BODY.APOLLO VALVES 94ALF10801BALL VALVE, INLET SIZE 2IN., LEAD FREE BRASS BODY,FULL-PORT, BLOW-OUT PROOF STEM DESIGNRAIN BIRD ESP-LXD-LXMMPED50 STATION, 2-WIRE DECODER BASED CONTROLLER INPOWDER COATED METAL, CABINET W/ PEDESTAL. (1)ESP-LXD 50-STATION, INDOOR/OUTDOOR, PLASTICWALL-MOUNT ENCLOSURE. INSTALL IN RAIN BIRDLXMM-LXMMPED POWDER COATED METAL CABINET W/PEDESTAL. SYSTEM REQUIREMENTS: RAIN BIRDFD-XXX-TURF FIELD DECODERS, PAIGE ELECTRIC CABLEP7072D & RAIN BIRD WC20 DRY SPLICES ONLY. GROUNDSYSTEM W/ (X) LSP-1TURF LINE SURGE PROTECTORS INRAIN BIRD ROUND VALVE BOXES. INSTALL PERMANUFACTURERS RECOMMENDATIONS.RAIN BIRD FD-X0XTURFFIELD DECODER FOR TWO-WIRE SYSTEM. INSTALL INVALVE BOX FOR VALVE. FD 101/102/202/401/601VALVE/SOLENOIDS. USE LINE SURGE PROTECTION ASPER MANUFACTURERFT.S DIRECTIONS.RAIN BIRD IQ4G-USAIQ NCC 4G CELLULAR CARTRIDGE UPGRADES ESP-LXSERIES CONTROLLERS TO IQ SATELLITE, FORCOMMUNICATION WITH IQ CENTRAL CONTROL. INCLUDEIQEXTANT4G EXTERNAL ANTENNA FOR METAL ORSTAINLESS STEEL CABINET/PEDESTAL. USED FOR DIRECTOR SERVER SATELLITE APPLICATIONS.RAIN BIRD LXIVMOUTFIELD DEVICE TO INTERFACE BETWEEN 3RD PARTYVALVES OR PUMP START RELAY & ESPLXIVM(P), 2-WIRECONTROLLERS. (1) LXIVMOUT PER VALVE/RELAY (DCLATCHING SOLENOID REQUIRED).POINT OF CONNECTION 2"EXISTING WELL #1POINT OF CONNECTION 2"EXISTING WELL #2IRRIGATION LATERAL LINE: PVC SCHEDULE 40IRRIGATION MAINLINE: PVC SCHEDULE 40 2"PIPE SLEEVE: PVC SCHEDULE 40LOCATE & USE EXISTING SLEEVESLSTRSTSST1000200030003500CFDIQLXWELL #1 (A)WELL #2 (B)Valve NumberValve FlowValve SizeValve Callout###"IRRIGATION SCHEDULENEIL RYANKINER232MNOTNAAOFT
ET
A
S
EEPACSDNALTCETI
HCRAENSEDLICSNCNRKL1.2251035BOZEMAN PUBLIC LIBRARY IRRIGATION RENOVATION
626 E MAIN STREET
BOZEMAN, MT 59715
IRRIGATION PLAN LANDSCAPE ARCHITECTURE & PLANNING
(406) 850-0461 www.secondnature.consultingDRAWN BYAPPROVEDDATEREVISIONSIRRIGATION PLAN SCALE: 1" = 20'0020'40'SCALE IN FEETFOR CONSTRUCTION DRIP LATERAL SHOWN INPAVEMENT FOR CLARITYLOCATION OF EXISTING SLEEVINGUNKNOWN, USE EXISTINGSLEEVING WHERE FEASIBLE, TYP.SEE SHEET L1.3
SEE SHEET L1.1
05-14-2026MAINTENANCE ,EDGE, TYP.MAINTENANCE ,EDGE, TYP.Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
WWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWYHDW WRAMPRAMP
RAMPRAMPRAMPRAMPRAMPLANDINGLANDINGLANDINGGGGGGGWSWSWSWSWSWSWSWSWSWSWSWWSWSWSWSFWSWSWSWSWSWS 4792479118 181820262026201818112"8A20.11"8A242416
16
1212
12 121616
181822202020202020202020202020202020202020202222222222222222222020202020202020202020202020222222222222181818181818 1814 14 10 8888888810 1216262626161614 1"1"1"112"1"10A30.3112"10A13A33.9112"13A11A19.31"11A12A20.71"12A9A11.71"9A1"112"1"1"1"1"112"1"1"1"1"112"1"1"1"112"1"1"1"1"112"2"2"1"FDFDSYMBOLMANUFACTURER/MODEL/DESCRIPTIONHUNTER MP STRIP RB 1806-SAM-P45TURF ROTATOR, 6IN. POP-UP WITH CHECK VALVE,PRESSURE REGULATED TO 45 PSI, MP ROTATOR NOZZLEON RB 1806 BODY.HUNTER MP1000 RB 1806-SAM-P45TURF ROTATOR, 6IN. POP-UP WITH CHECK VALVE,PRESSURE REGULATED TO 45 PSI, MP ROTATOR NOZZLEON RB 1806 BODY.HUNTER MP2000 RB 1806-SAM-P45TURF ROTATOR, 6IN. POP-UP WITH CHECK VALVE,PRESSURE REGULATED TO 45 PSI, MP ROTATOR NOZZLEON RB 1806 BODY.HUNTER MP3000 RB 1806-SAM-P45TURF ROTATOR, 6IN. POP-UP WITH CHECK VALVE,PRESSURE REGULATED TO 45 PSI, MP ROTATOR NOZZLEON RB 1806 BODY.HUNTER MP3500 RB 1806-SAM-P45TURF ROTATOR, 6IN. POP-UP WITH CHECK VALVE,PRESSURE REGULATED TO 45 PSI, MP ROTATOR NOZZLEON RB 1806 BODY.SYMBOLMANUFACTURER/MODEL/DESCRIPTIONRAIN BIRD XCZ-100-LC 1"WIDE FLOW DRIP CONTROL KIT, FOR COMMERCIAL USES.1IN. PESB VALVE, WITH 1IN. PRESSURE REGULATING 40PSIBASKET FILTER. 0.3-20 GPM.RAIN BIRD XCZ-150-LCDR 1-1/2"HIGH FLOW CONTROL ZONE KIT, FOR LARGE COMMERCIALDRIP ZONES. 1-1/2IN. PESB-R SCRUBBER GLOBE VALVEWITH HIGH-CAPACITY FILTER AND PRESSURE REGULATINGSYSTEM (PRS) FIXED AT 40PSI. FLOW RANGE: 20 - 62 GPM.AREA TO RECEIVE DRIPLINERAIN BIRD XFCV-06-12XFCV XON-SURFACE LANDSCAPE DRIPLINE WITH AHEAVY-DUTY 3.5 PSI CHECK VALVE. 0.6 GPH EMITTERS AT12" O.C. DRIPLINE LATERALS SPACED AT 12" APART, WITHEMITTERS OFFSET FOR TRIANGULAR PATTERN. GREATFOR ELEVATION CHANGE. SPECIFY XF INSERT FITTINGS.SYMBOLMANUFACTURER/MODEL/DESCRIPTIONRAIN BIRD PESB 1"1IN., 1-1/2IN., 2IN., 3IN., 3IN. PLASTIC INDUSTRIAL REMOTECONTROL VALVE. LOW FLOW OPERATING CAPABILITY,GLOBE CONFIGURATION. WITH SCRUBBER TECHNOLOGYFOR RELIABLE PERFORMANCE IN DIRTY WATERIRRIGATION APPLICATIONS.RAIN BIRD 5-RC 1"1IN. BRASS QUICK-COUPLING VALVE, WITHCORROSION-RESISTANT STAINLESS STEEL SPRING,THERMOPLASTIC RUBBER COVER, AND 1-PIECE BODY.APOLLO VALVES 94ALF10801BALL VALVE, INLET SIZE 2IN., LEAD FREE BRASS BODY,FULL-PORT, BLOW-OUT PROOF STEM DESIGNRAIN BIRD ESP-LXD-LXMMPED50 STATION, 2-WIRE DECODER BASED CONTROLLER INPOWDER COATED METAL, CABINET W/ PEDESTAL. (1)ESP-LXD 50-STATION, INDOOR/OUTDOOR, PLASTICWALL-MOUNT ENCLOSURE. INSTALL IN RAIN BIRDLXMM-LXMMPED POWDER COATED METAL CABINET W/PEDESTAL. SYSTEM REQUIREMENTS: RAIN BIRDFD-XXX-TURF FIELD DECODERS, PAIGE ELECTRIC CABLEP7072D & RAIN BIRD WC20 DRY SPLICES ONLY. GROUNDSYSTEM W/ (X) LSP-1TURF LINE SURGE PROTECTORS INRAIN BIRD ROUND VALVE BOXES. INSTALL PERMANUFACTURERS RECOMMENDATIONS.RAIN BIRD FD-X0XTURFFIELD DECODER FOR TWO-WIRE SYSTEM. INSTALL INVALVE BOX FOR VALVE. FD 101/102/202/401/601VALVE/SOLENOIDS. USE LINE SURGE PROTECTION ASPER MANUFACTURERFT.S DIRECTIONS.RAIN BIRD IQ4G-USAIQ NCC 4G CELLULAR CARTRIDGE UPGRADES ESP-LXSERIES CONTROLLERS TO IQ SATELLITE, FORCOMMUNICATION WITH IQ CENTRAL CONTROL. INCLUDEIQEXTANT4G EXTERNAL ANTENNA FOR METAL ORSTAINLESS STEEL CABINET/PEDESTAL. USED FOR DIRECTOR SERVER SATELLITE APPLICATIONS.RAIN BIRD LXIVMOUTFIELD DEVICE TO INTERFACE BETWEEN 3RD PARTYVALVES OR PUMP START RELAY & ESPLXIVM(P), 2-WIRECONTROLLERS. (1) LXIVMOUT PER VALVE/RELAY (DCLATCHING SOLENOID REQUIRED).POINT OF CONNECTION 2"EXISTING WELL #1POINT OF CONNECTION 2"EXISTING WELL #2IRRIGATION LATERAL LINE: PVC SCHEDULE 40IRRIGATION MAINLINE: PVC SCHEDULE 40 2"PIPE SLEEVE: PVC SCHEDULE 40LOCATE & USE EXISTING SLEEVESLSTRSTSST1000200030003500CFDIQLXWELL #1 (A)WELL #2 (B)Valve NumberValve FlowValve SizeValve Callout###"IRRIGATION SCHEDULENEIL RYANKINER232MNOTNAAOFT
ET
A
S
EEPACSDNALTCETI
HCRAENSEDLICSNCNRKL1.3251035BOZEMAN PUBLIC LIBRARY IRRIGATION RENOVATION
626 E MAIN STREET
BOZEMAN, MT 59715
IRRIGATION PLAN LANDSCAPE ARCHITECTURE & PLANNING
(406) 850-0461 www.secondnature.consultingDRAWN BYAPPROVEDDATEREVISIONSIRRIGATION PLAN SCALE: 1" = 20'0020'40'SCALE IN FEETFOR CONSTRUCTION LOCATION OF EXISTING SLEEVINGUNKNOWN, USE EXISTINGSLEEVING WHERE FEASIBLE, TYP.LOCATION OF EXISTING SLEEVINGUNKNOWN, USE EXISTINGSLEEVING WHERE FEASIBLE, TYP.MAINTENANCE EDGE05-14-2026LOCATION OF EXISTING SLEEVINGUNKNOWN, USE EXISTINGSLEEVING WHERE FEASIBLE, TYP.Generated:2026-04-03 16:15P.O.C. NUMBER: 01Water Source Information:Existing Well #1FLOW AVAILABLECustom Max Flow:35 GPMFlow Available35 GPMPRESSURE AVAILABLEStatic Pressure at POC:70 PSIPressure Available:70 PSIDESIGN ANALYSISMaximum Station Flow:33.91 GPMFlow Available at POC:35 GPMResidual Flow Available:1.09 GPMCritical Station:4B Design Pressure:40 PSI Friction Loss:1.59 PSI Fittings Loss:0.16 PSI Elevation Loss:0 PSI Loss through Valve:5.98 PSIPressure Req. at Critical Station:47.7 PSILoss for Fittings:0.16 PSILoss for Main Line:1.65 PSILoss for POC to Valve Elevation:0 PSILoss for Backflow:0 PSICritical Station Pressure at POC:49.5 PSIPressure Available:70 PSIResidual Pressure Available:20.5 PSICRITICAL ANALYSISGenerated:2026-04-16 15:24P.O.C. NUMBER: 02Water Source Information:Existing Well #2FLOW AVAILABLECustom Max Flow:35 GPMFlow Available35 GPMPRESSURE AVAILABLEStatic Pressure at POC:70 PSIPressure Available:70 PSIDESIGN ANALYSISMaximum Station Flow:31.20 GPMFlow Available at POC:35 GPMResidual Flow Available:3.80 GPMPressure Req. at Critical Station:0 PSILoss for Fittings:0 PSILoss for Main Line:0 PSILoss for POC to Valve Elevation:0 PSILoss for Backflow:0 PSICritical Station Pressure at POC:0 PSIPressure Available:70 PSIResidual Pressure Available:70 PSICRITICAL ANALYSISDocusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
NEIL RYANKINER232MNOTNAAOFT
ET
A
S
EEPACSDNALTCETI
HCRAENSEDLICSNCNRKL2.1251035BOZEMAN PUBLIC LIBRARY IRRIGATION RENOVATION
626 E MAIN STREET
BOZEMAN, MT 59715
IRRIGATION DETAILS LANDSCAPE ARCHITECTURE & PLANNING
(406) 850-0461 www.secondnature.consultingDRAWN BYAPPROVEDDATEREVISIONSFOR CONSTRUCTION05-14-2026POINT OF CONNECTION 1" = 1'-0"2" IRRIGATION MAINLINEQUICK COUPLER FORWINTERIZATIONMASTER VALVE,NORMALLY OPENIRRIGATION MAIN FROM WELLWMVEXISTING EXEMPT WELL WITHNEW VFD & PRESSURE TANKASSEMBLY, CONTROLSQC2" IRRIGATIONMAINLINE TO TEELINE SIZE BALL VALVE2" IRRIGATION MAINLINEFSULTRASONICFLOW SENSORFFILTER, IF NEEDEDBID ALTERNATE #1:AMIAD 2-A-MSIG-STEEL SCREEN 100MMAMIAD 2IN. MINI SIGMA, ANGLEDSELF-CLEANING FILTER, BSPT OR NPTINLET-OUTLET. STAINLESS STEELWEAVEWIRE SCREEN ELEMENT. ADI-PBLUETOOTH RANGE CONTROLLER.(1) FOR EACH WELLNOTE: TWO POINTS OF CONNECTIONARE REQUIRED FOR THIS PROJECT.1P-CO-BOZLIB-08ESP-LXIVM/PRO CONTROLLER IN METAL PEDESTAL1" = 1'-0"KEY SPECIFICATIONSMAX PROGRAMS
STATIONS
MASTER SIMULATIONS
MASTER VALVES
FLOW SENSORS
WEATHER SENSORSLXME2LXME2 PROFEATUREMODEL106" MIN.123456406024081651051048MIN.2% SLOPE AWAYFROM PEDESTAL789101112OPTIONAL EXTERIOR CELLULAR ANTENNA IF USING IQ4 CELLULAR CARTRIDGE1CONVENTIONAL ESP-LXME2 CONTROLLER: RAIN BIRD ESP-LXME2/PRO WITH LXMM METAL OR LXMMSS STAINLESS STEEL CABINET ANDLXMMPED METAL OR LXMMSSPED STAINLESS STEEL PEDESTAL. INSTALL CONTROLLER, CABINET AND PEDESTAL PER MANUFACTURER'SRECOMMENDATIONS. OPTIONAL IQ4 CARTRIDGE, REFERENCE LEGEND FOR MODEL2CONCRETE PAD: 6-INCH MIN. THICKNESS. 6-INCHES LARGER ON ALL SIDES THAN PEDESTAL FOOTPRINT3FINISH GRADE4POWER SUPPLY WIRE51-INCH SCH 40 PVC CONDUIT, FITTINGS AND SWEEP ELL FOR POWER SUPPLY62-INCH SCH 40 PVC CONDUIT, FITTINGS AND SWEEP ELL FOR TWO-WIRE CABLE7MAXI WIRE TWO-WIRE PATH TO FIELD DEVICES, USE A DIFFERENT CABLE JACKET COLOR FOR EACH PATH8COMPACTED SUBGRADE91-INCH SCH 40 PVC CONDUIT, FITTINGS AND SWEEP ELL FOR GROUNDING WIRE, REF. NOTE 210IF APPLICABLE, 1-INCH SCH 40- PVC CONDUIT, FITTINGS AND SWEEP ELL FOR IQ COMMUNICATION WIRE11IF APPLICABLE, COMMUNICATION WIRE, REFERENCE LEGEND FOR TYPE.OPTIONS:A. RS232 SERIAL CABLE TO CENTRAL CONTROL COMPUTERB. ETHERNET CABLE TO LOCAL NETWORK JACKC. PE-CABLE OR Y-CABLE FOR EXTERNAL RADIO TO CLIENT SATELLITECONTROLLERS12NOTES:1.ESP-LXIVM CONTROLLER IS AVAILABLE IN TWO MODELS.THE LXIVMWITH 60 STATIONS AND THE LXIVM-PROWITH 240 STATIONS. REFERTO THE CHART FOR DIFFERENCES BETWEEN THE TWO MODELS.2.PROVIDE PROPER GROUNDING COMPONENTS TO ACHIEVE GROUNDRESISTANCE OF 10 OHMS OR LESS.2P-CO-BOZLIB-66NOTES:1. USE TEFLON TAPE FOR ALL THREADED PIPE CONNECTIONS.2. ALL WIRES TO BE INSTALLED AS PER LOCAL CODES. NO ''IN-LINE'' WIRE SPLICES WILL BE ALLOWED.ELECTRIC CONTROL VALVE1" = 1'-0"PVC MALE ADAPTOR & LATERAL LINEFINISH GRADE12" STANDARD VALVE BOXSCH. 80 UNIONCENTER VALVE IN BOXSCH. 80 NIPPLESCH. 40 PVC SxS 90CLASS 200 PVC PIPECONTROL WIRESCH. 40 PVC TEE OR 90ANGLE TO DIRECTLATERAL IN TRENCHSUCH THAT PIPE IS NOTCURVED OR OTHERWISESTRESSEDDRAIN GRAVEL1 CU. FOOTDOUBLE VALVEBOXES BOLTEDBACK TO BACK12"
18" MIN3P-CO-BOZLIB-09DRIP ZONE KIT IN VALVE BOXNOT TO SCALE1FINISH GRADE12LANDSCAPE PRODUCTS JUMBO VALVE BOXWITH COVER23VALVE ID TAG34CONTROLWIRE45LANDSCAPE PRODUCTS DRIP KIT(INCLUDES VALVE, FILTER & PRESSUREREGULATOR)56PVC SUPPLY HEADER TO DRIPLINE67PVC SCH 80 FEMALE ADAPTER OR REDUCER78PVC SCH 80 ELL89PVC SCH 80 NIPPLE (LENGTH AS REQUIRED)910PVC SCH 80 TEE OR ELL101112PVC MAINLINE113" MINIMUM DEPTH OF 3/4" WASHED GRAVEL1213PVC SCH 80 STREET ELL1314MANUAL FLUSH POINT14P-CO-BOZLIB-104VALVE CLUSTER PLANNOTES:1. USE TEFLON TAPE FOR ALL THREADED PIPE CONNECTIONS.2. ALL WIRES TO BE INSTALLED AS PER LOCAL CODES. NO ''IN-LINE'' WIRE SPLICES WILL BE ALLOWED.3. DOUBLE UP VALVE BOXES TO PROVIDE ADEQUATE SPACE BELOW VALVE.CONTROL VALVE CLUSTER 1" = 1'-0"VALVE BOXCARSON OR EQUALMAINLINE AS PER PLANSET VALVES SIDE BY SIDEAS SHOW MAX 5 PER BOX2"5P-CO-BOZLIB-01NOTE:WET TRENCHES THOROUGHLYFOLLOWING BACKFILL PROCEDURE.BACKFILL TO PREVENT FUTURE SETTLINGMAINLINE & LATERAL LINE BEDDING1" = 1'-0"COMPACTED NATIVEBACKFILL FREE OFROCKS & CLOGSCONTROL WIRE3"MAINLINE ORLATERAL LINE18" LATERAL
24" MAINLINE TOPSOILFINISH GRADE6P-CO-BOZLIB-23QUICK COUPLER1" = 1'-0"VALVE BOXQUICK COUPLERSET VALVE BOX FLUSH WITH FINISH GRADE34" CLEAR WASHED ROCKFACTORY O RING SWING JOINTSTAINLESS HOSE CLAMP TO HOLD QC VALVETO STEEL STAKESTEEL STAKEPVC MAINLINE7P-CO-ANN 6.7-11FINISHED GRADE.FROM WELL2131211761098FLOW1SPECIFIED RECTANGULAR VALVEBOXES WITH EXTENSIONS AS NEEDED2NOT USED3NOT USED4NOT USED52" GALVANIZED FLANGE X 1 PTADAPTER.6PVC SCH 80 2"X8" NIPPLE.7MASTER VALVE AS SPECIFIED.8WATER PROOF CONNECTORS.92X24 PVC SCH 80 TOE PIPING.102X6X16 CONCRETE WALL CAPS,TWO PER BOX, ONE EACH SIDE.11FLOW METER AS SPECIFIED (2WIRES TO CONTROLLER).122X12 PVC SCH 80 PIPING.13NOT USED14NOT USED24" MINIMUM.10 X DIAMETER OF PIPE.MASTER VALVE & FLOW SENSOR3/4" = 1'-0"P-CO-BOZLIB-288ULTRASONIC FLOW SENSOR3" = 1'-0"NOTES:1.THE UFS CAN BE INSTALLED IN A VERTICAL POSITION WITH THE FLOW ARROW POINTING UPWARDS.2.THE UFS SIZE MUST BE EQUAL TO OR SMALLER THAN THE INCOMING PIPE SIZE.3.THE UFS DOES NOT REQUIRE STRAIGHT PIPE BEFORE OR AFTER SENSOR PLACEMENT.4.NO BRICKS REQUIRED FOR RAIN BIRD VB-SERIES VALVE BOXES ONLY.MODELSIZEKOFFSETFLOW RANGEUFS1001"0.73-1.660.3 - 50 GPMUFS1501.5"1.70-0.3160.5 - 110 GPMUFS2002"2.8490.14391.0 - 200 GPM12345678910RAIN BIRD UFS SERIESFLOW SENSOR, SEELEGEND FOR MODEL136" LENGTH OF COILEDCONTROL WIRE23" MIN. DEPTH OF 3/4"WASHED GRAVEL3BRICK (1 OF 4),IF APPLICABLE4RAIN BIRD VB SERIESVALVE BOX W/ LID5FINISH GRADE6REFERENCE MANUALFOR WIRINGINSTALLATIONINSTRUCTIONS7CONCENTRICREDUCER8PVC CLOSE NIPPLE(1 OF 2)9PVC UNION (1 OF 2)109P-CO-BOZLIB-64STREAM SPRAYS3" = 1'-0"1806 RAINBIRD SPRAY BODY WITHHUNTER MP-ROTATOR NOZZLESFINISH GRADESCH 40 THREADED COUPLERSCH 80 NIPPLELATERAL TEE OR ELLLATERAL PIPE1/2" PVC STREET ELLS (3)10P-CO-BOZLIB-68Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
NEIL RYANKINER232MNOTNAAOFT
ET
A
S
EEPACSDNALTCETI
HCRAENSEDLICSNCNRKL2.2251035BOZEMAN PUBLIC LIBRARY IRRIGATION RENOVATION
626 E MAIN STREET
BOZEMAN, MT 59715
IRRIGATION DETAILS LANDSCAPE ARCHITECTURE & PLANNING
(406) 850-0461 www.secondnature.consultingDRAWN BYAPPROVEDDATEREVISIONSFOR CONSTRUCTION05-14-20262" LINEFROM WELL2" MAIN LINEENCLOSURE SIZE PLUS 6"LENGTH AND WIDTHHEIGHT AS PERLOCAL CODEBACKFLOW PREVENTER ENCLOSURE1" = 1'-0"REDUCED PRESSUREBACKFLOW DEVICE ASSPECIFIED - OR REUSEEXISTING IF ALLOWEDCLAMSHELL STEELENCLOSURE STRONGBOX,OR EQUAL - SIZED AS NEEDEDCONCRETETHRUSTBLOCKSGALVANIZED NIPPLES& ELLS AS REQUIREDGALVANIZED UNIONSAT EACH SIDE, TYP.GALVANIZED RISERS, TYP.4" THICK CONCRETE PADGALVANIZED NIPPLES& ELLS AS REQUIREDPVC COUPLER OR REDUCERAS REQUIRED, TYP.SCHEDULE 40 SLEEVES1P-CO-ANN 6.7-71NOTES:1- LOCATE VALVE BOXES IN PLANTING AREAS, WHERE FEASIBLE.2- WRAP VALVE BOX WITH A MINIMUM OF 3 MIL THICK PLASTIC AND SECURE IT USING DUCT TAPE OR ELECTRICAL TAPE.3- ALL THREADED CONNECTION TO BE MADE USING TEFLON TAPE.4- ALL CHANGES IN ELEVATION SHALL BE MADE USING SCH. 40 PVC 45° ELBOWS.6" MIN
12" MAX THREADED BALL VALVE. (SEEIRRIGATION LEGEND FOR MAKE AND MODEL).SCH. 80 PVC MALE ADAPTER.FINISHED GRADE.RECTANGULAR VALVE BOX WITHLOCKING LID.PAVEMENT.SCH. 80 PVC UNION SXS.SCH. 80 PVC NIPPLE TXS.MAINLINE.THREE INCH (3") THICK LAYEROF PEA GRAVEL OR APPROVED38" WELDED WIRE MESH.SCH. 40 PVC 45° ELBOW.FOUR (4) 4" X 8" BRICKS.BALL VALVE DETAIL1 1/2" = 1'-0"P-CO-BOZLIB-292SURGE PROTECTOR W/ GROUNDING ROD1 1/2" = 1'-0"NOTES:1.INSTALL SURGE PROTECTOR ON ITS OWN OR A VALVE IN THE SAME VALVE BOX.2.NO OTHER WIRES OR CABLES SHALL BE INSTALLED WITHIN THE SPHERE OF INFLUENCE.3.INSTALL THE CONNECTING WIRE IN AS STRAIGHT A LINE AS POSSIBLE. IF YOU MUST MAKE A TURN OR BENDIN THE WIRE, MAKE THE TURN IN A SWEEPING CURVE WITH A MAXIMUM RADIUS OF EIGHT INCHES ANDMINIMUM INCLUDED ANGLE OF 90°.4.TO MINIMIZE RESISTANCE, THE COPPER WIRE MUST BE PRE-WELDED TO THE GROUNDING RODS/PLATES,OR WELDED TO THE RODS/PLATES USING AN EXOTHERMIC WELDING PROCESS AT THE SITE.5.MAKE SURE ALL WELDS ARE SECURE BEFORE BURYING THE GROUNDING RODS. RODS AND PLATES WITHWELDED JOINTS DO NOT NEED PERIODIC VISUAL INSPECTION AND CAN BE FULLY BURIED.8' MIN.12" MIN.123456789RAIN BIRD VALVE BOX 6" ROUND1SURGE PROTECTOR, SEE LEGEND2TWO-WIRE MAXI-WIRE PATH3#6 AWG OR LARGER SOLID BARE COPPER WIRE4COPPER CLAD GROUNDNG ROD (5/8" x 8')5FINISH GRADE6COPPER WIRE7GROUND ENHANCEMENT, IF APPLICABLE8CADWELD CONNCECTION93P-CO-BOZLIB-652"-4"INSET BINSET AINSET ANOTES:1. FOR ALL XFS-CV AND POLY CONNECTIONS INSTALL XFF AND/OR XFDFITTINGS.2. DISTANCE BETWEEN LATERAL ROWS AND EMITTER SPACING TO BEBASED ON SOIL TYPE, PLANT MATERIALS AND CHANGES INELEVATION. SEE INSTALLATION SPECIFICATIONS ON RAIN BIRD WEBSITE (WWW.RAINBIRD.COM) FOR SUGGESTED SPACING.3. LENGTH OF LONGEST DRIPLINE LATERAL SHOULD NOT EXCEED THEMAXIMUM SPACING PER MANUFACTURE'S RECOMMENDATIONS.2-3"MULCHINSET B ON-GRADEINSET B SUB-GRADE2-3"MULCHON-GRADE DRIPLINE LAYOUT W PVC HEARDER-CENTER FEEDN.T.SLENGTH VARIES, FOR DRIPLINE MAX DISTANCE,REF. MANUFACTURER'S RECOMMENDATIONS1
PVC EXHAUST HEADER12OPEREATION INDICATORRAIN BIRD MODEL: OPERIND23XF SERIES TIE-DOWN STAKES (TDS-050)REFER TO RAIN BIRD DRIPLINE DESIGN GUIDE FOR PROPERSPACING34FLUSH POINT (TYPICAL), INSTALL AT LOWEST PART OFDRIPLINE SECTION45PVC TEE OR ELL W/ RAIN BIRD XFF-MA FITTING56ON-GRADE RAIN BIRD DRIPLINE, REF. LEGEND FOR MODEL67CONNECTION FROM SUPPLY MANIFOLD TO DRIPLINE(TYPICAL)- SEE INSET A78RAIN BIRD CONTROL ZONE DRIP KIT, REF. LEGEND FOR MODEL89PVC SUPPLY PIPE FROM RAIN BIRD CONTROL ZONE KIT (SIZEDTO MEET LATERAL FLOW DEMAND)910AIR RELIEF VALVE, INSTALL AT HIGHEST PART OF DRIPLINESECTIONRAIN BIRD MODEL: ARV0501011PERIMETER DRIPLINE PIPE TO BE INSTALLED 2"-4" FROMPERIMETER OF AREA1112XFF - MA - 050 FITTING1213SCH 40 PVC TEE1314PVC SCH 40 RISER PIPE1415PVC CENTER FEED HEADER15136655111FINISH GRADEFINISH GRADEFINISH GRADE4IN
OUT OUT
A
HP
2" NPT2AVIN2" NPTRECYCLED WATERDO NOT DR
INK7 764 "123456789101112131410 2764 "1' 8 2164 "15162'-6 34 "1'-9 1964 "17182" ON LINE MINI SIGMA UNIT111/2" GALVANIZED PIPE DISCHARGEPIPE "OPEN TO ATMOSPHERE"252"L, 30"H, XX"W3STRONGBOX SBBC-52AL4WELL WATER STICKERDO NOT DRINK5LANDSCAPE66"X10" CONCRETE PAD73/4" CRUSHED GRAVELSUMP BOX8MAINLINE9NATIVE SOIL102" BRASS UNION/ NIPPLE112" BRASS GATE VALVE12SECURED SWIVEL MOUNTING PLATES13FINISH GRADE142" GALVANIZED NIPPLE152" CLASS 315 PVC PIPE16LANDSCAPE FABRIC172" GALVANIZED ELBOW18MINI SIGMA WATER FILTRATION UNIT1/2" = 1'-0"BID ALTERNATE #1P-CO-ANN 6.7-275Docusign Envelope ID: 590FFC59-6E62-87B2-800B-87886EDADAAD
Certificate Of Completion
Envelope Id: 590FFC59-6E62-87B2-800B-87886EDADAAD Status: Completed
Subject: Complete with Docusign: PSA_-_Potts_Drilling_Inc._-_Library_Irrigation_Wells_VFD_Upgrades.pdf
Source Envelope:
Document Pages: 24 Signatures: 3 Envelope Originator:
Certificate Pages: 5 Initials: 0 Alex Newby
AutoNav: Enabled
EnvelopeId Stamping: Enabled
Time Zone: (UTC-08:00) Pacific Time (US &
Canada)
Stamps: 1 alex.newby@bozemanmt.gov
IP Address: 155.190.9.6
Record Tracking
Status: Original
6/8/2026 3:10:36 PM
Holder: Alex Newby
alex.newby@bozemanmt.gov
Location: DocuSign
Security Appliance Status: Connected Pool: StateLocal
Signer Events Signature Timestamp
Ben Minden
ben@pottsdrilling.com
President
Security Level: Email, Account Authentication
(None)Signature Adoption: Pre-selected Style
Using IP Address: 69.146.170.122
Sent: 6/9/2026 4:00:11 PM
Viewed: 6/10/2026 8:01:28 AM
Signed: 6/10/2026 8:01:50 AM
Electronic Record and Signature Disclosure:
Accepted: 6/10/2026 8:01:28 AM
ID: 3ba16850-4d59-4b67-aa9f-e3a5835e26ba
Greg Sullivan
greg.sullivan@bozemanmt.gov
City of Bozeman
Security Level: Email, Account Authentication
(None)Signature Adoption: Pre-selected Style
Using IP Address: 155.190.3.7
Sent: 6/10/2026 8:01:53 AM
Viewed: 6/10/2026 11:21:29 AM
Signed: 6/10/2026 11:21:41 AM
Electronic Record and Signature Disclosure:
Accepted: 6/10/2026 11:21:29 AM
ID: 3e31cd68-fc13-4a59-8b42-1f5b4db0a3e6
Chuck Winn
chuck.winn@bozemanmt.gov
City Manager
15
Security Level: Email, Account Authentication
(None)
Signature Adoption: Pre-selected Style
Using IP Address: 69.145.13.76
Sent: 6/10/2026 11:21:45 AM
Viewed: 6/10/2026 5:19:23 PM
Signed: 6/10/2026 5:19:53 PM
Electronic Record and Signature Disclosure:
Accepted: 6/10/2026 5:19:23 PM
ID: 2cfae45c-ffa8-46c4-9ec9-f56d1ec16ef3
Mike Maas
mike.maas@bozemanmt.gov
City Clerk
City of Bozeman
Security Level: Email, Account Authentication
(None)Using IP Address: 155.190.3.7
Sent: 6/10/2026 5:19:55 PM
Viewed: 6/12/2026 1:28:06 PM
Signed: 6/12/2026 1:28:13 PM
Electronic Record and Signature Disclosure:
Accepted: 8/23/2022 2:22:44 PM
ID: b1bb90fd-5db8-4a5f-9451-9536f39ef003
In Person Signer Events Signature Timestamp
Editor Delivery Events Status Timestamp
Agent Delivery Events Status Timestamp
Intermediary Delivery Events Status Timestamp
Certified Delivery Events Status Timestamp
Carbon Copy Events Status Timestamp
Max Ziegler
max.ziegler@bozemanmt.gov
Security Level: Email, Account Authentication
(None)
Sent: 6/9/2026 4:00:10 PM
Viewed: 6/11/2026 7:12:09 AM
Electronic Record and Signature Disclosure:
Not Offered via Docusign
Michelle Chapel
michelle.chapel@bozemanmt.gov
Records Coordinator
City Bozeman
Security Level: Email, Account Authentication
(None)
Sent: 6/12/2026 1:28:15 PM
Electronic Record and Signature Disclosure:
Accepted: 2/24/2026 9:38:21 AM
ID: 1fa4538c-9b38-40d2-9e1a-390aa0445f47
Witness Events Signature Timestamp
Notary Events Signature Timestamp
Envelope Summary Events Status Timestamps
Envelope Sent Hashed/Encrypted 6/9/2026 4:00:10 PM
Certified Delivered Security Checked 6/12/2026 1:28:06 PM
Signing Complete Security Checked 6/12/2026 1:28:13 PM
Completed Security Checked 6/12/2026 1:28:15 PM
Payment Events Status Timestamps
Electronic Record and Signature Disclosure
ELECTRONIC RECORD AND SIGNATURE DISCLOSURE
From time to time, City Manager (we, us or Company) may be required by law to provide to you
certain written notices or disclosures. Described below are the terms and conditions for providing
to you such notices and disclosures electronically through the DocuSign system. Please read the
information below carefully and thoroughly, and if you can access this information electronically
to your satisfaction and agree to this Electronic Record and Signature Disclosure (ERSD), please
confirm your agreement by selecting the check-box next to ‘I agree to use electronic records and
signatures’ before clicking ‘CONTINUE’ within the DocuSign system.
Getting paper copies
At any time, you may request from us a paper copy of any record provided or made available
electronically to you by us. You will have the ability to download and print documents we send
to you through the DocuSign system during and immediately after the signing session and, if you
elect to create a DocuSign account, you may access the documents for a limited period of time
(usually 30 days) after such documents are first sent to you. After such time, if you wish for us to
send you paper copies of any such documents from our office to you, you will be charged a
$0.00 per-page fee. You may request delivery of such paper copies from us by following the
procedure described below.
Withdrawing your consent
If you decide to receive notices and disclosures from us electronically, you may at any time
change your mind and tell us that thereafter you want to receive required notices and disclosures
only in paper format. How you must inform us of your decision to receive future notices and
disclosure in paper format and withdraw your consent to receive notices and disclosures
electronically is described below.
Consequences of changing your mind
If you elect to receive required notices and disclosures only in paper format, it will slow the
speed at which we can complete certain steps in transactions with you and delivering services to
you because we will need first to send the required notices or disclosures to you in paper format,
and then wait until we receive back from you your acknowledgment of your receipt of such
paper notices or disclosures. Further, you will no longer be able to use the DocuSign system to
receive required notices and consents electronically from us or to sign electronically documents
from us.
All notices and disclosures will be sent to you electronically
Electronic Record and Signature Disclosure created on: 4/22/2022 3:30:54 PM
Parties agreed to: Ben Minden, Greg Sullivan, Chuck Winn, Mike Maas, Michelle Chapel
Unless you tell us otherwise in accordance with the procedures described herein, we will provide
electronically to you through the DocuSign system all required notices, disclosures,
authorizations, acknowledgements, and other documents that are required to be provided or made
available to you during the course of our relationship with you. To reduce the chance of you
inadvertently not receiving any notice or disclosure, we prefer to provide all of the required
notices and disclosures to you by the same method and to the same address that you have given
us. Thus, you can receive all the disclosures and notices electronically or in paper format through
the paper mail delivery system. If you do not agree with this process, please let us know as
described below. Please also see the paragraph immediately above that describes the
consequences of your electing not to receive delivery of the notices and disclosures
electronically from us.
How to contact City Manager:
You may contact us to let us know of your changes as to how we may contact you electronically,
to request paper copies of certain information from us, and to withdraw your prior consent to
receive notices and disclosures electronically as follows:
To contact us by email send messages to: mmaas@bozeman.net
To advise City Manager of your new email address
To let us know of a change in your email address where we should send notices and disclosures
electronically to you, you must send an email message to us at mmaas@bozeman.net and in the
body of such request you must state: your previous email address, your new email address. We
do not require any other information from you to change your email address.
If you created a DocuSign account, you may update it with your new email address through your
account preferences.
To request paper copies from City Manager
To request delivery from us of paper copies of the notices and disclosures previously provided
by us to you electronically, you must send us an email to mmaas@bozeman.net and in the body
of such request you must state your email address, full name, mailing address, and telephone
number. We will bill you for any fees at that time, if any.
To withdraw your consent with City Manager
To inform us that you no longer wish to receive future notices and disclosures in electronic
format you may:
i. decline to sign a document from within your signing session, and on the subsequent page,
select the check-box indicating you wish to withdraw your consent, or you may;
ii. send us an email to mmaas@bozeman.net and in the body of such request you must state your
email, full name, mailing address, and telephone number. We do not need any other information
from you to withdraw consent.. The consequences of your withdrawing consent for online
documents will be that transactions may take a longer time to process..
Required hardware and software
The minimum system requirements for using the DocuSign system may change over time. The
current system requirements are found here: https://support.docusign.com/guides/signer-guide-
signing-system-requirements.
Acknowledging your access and consent to receive and sign documents electronically
To confirm to us that you can access this information electronically, which will be similar to
other electronic notices and disclosures that we will provide to you, please confirm that you have
read this ERSD, and (i) that you are able to print on paper or electronically save this ERSD for
your future reference and access; or (ii) that you are able to email this ERSD to an email address
where you will be able to print on paper or save it for your future reference and access. Further,
if you consent to receiving notices and disclosures exclusively in electronic format as described
herein, then select the check-box next to ‘I agree to use electronic records and signatures’ before
clicking ‘CONTINUE’ within the DocuSign system.
By selecting the check-box next to ‘I agree to use electronic records and signatures’, you confirm
that:
You can access and read this Electronic Record and Signature Disclosure; and
You can print on paper this Electronic Record and Signature Disclosure, or save or send
this Electronic Record and Disclosure to a location where you can print it, for future
reference and access; and
Until or unless you notify City Manager as described above, you consent to receive
exclusively through electronic means all notices, disclosures, authorizations,
acknowledgements, and other documents that are required to be provided or made
available to you by City Manager during the course of your relationship with City
Manager.