HomeMy WebLinkAbout012 A1.2.1 ASSEMBLY TYPESEXAMPLE:= TYPE 'A' WALL, WITH 6" STUDS, TILE BACKER
BOARD ('T'), AND A 2-HOUR FIRE RATING
(PER U.L. DESCRIPTION)
ADDITIONAL WALL COMPONENTS:
SOUND BATTS (S)/
TILE BACKER (T)/
WET WALL (W)/
PARTIAL HEIGHT (P)/
VAPOR PERMEABLE AIR BARRIER (V)
LOW WALL (L)
ACOUSTICAL STC RATING
TYPE
(A - Z)
STUD/MATERIAL
WIDTH
1 B-4 T
WALL TYPE LEGEND
FIRE RATING
2A-6T
FIN. FLOOR, TYP.
UNDERSIDE OF DECK
OR BEAM ABOVE, TYP.
CONT. SEALANT
BOTH SIDES, TYP.
SYMBOL:
CONT. SEALANT
BOTH SIDES, TYP.
STUD SIZE
WALL TYPE
METAL STUD WITH
GB-1 EACH SIDE
SLIP TRACK
A SERIES PARTITIONA
1 5/8" (1)
2 1/2" (2)
3 5/8" (3)
6" (6)A-6
1-HOUR RATING UL DES U465 (MTL)
FIN. FLOOR, TYP.
UNDERSIDE OF DECK
OR BEAM ABOVE, TYP.
CONT. SEALANT
BOTH SIDES, TYP.
CONT. SEALANT
BOTH SIDES, TYP.
METAL STUD WITH 1
LAYER GBX-1 EACH
SIDE
SLIP TRACK
1 5/8" (1)
2 1/2" (2)
3 5/8" (3)
6" (6)
FIN. FLOOR, TYP.
UNDERSIDE OF DECK
OR BEAM ABOVE, TYP.
CONT. SEALANT
BOTH SIDES, TYP.
CONT. SEALANT
BOTH SIDES, TYP.
GBI-1
SLIP TRACK
6" (6)A-6A2
A SERIES ACOUSTICAL PARTITIONS NON-RATED
3/4" HAT ONE-LEGGED
CHANELS AT 24" O.C.,
VERTICALLY
METAL STUD AT 16"
O.C.
FILL CAVITY WITH
ACOUSTICAL GLASS
BATT INSULATION
ACOUSTICAL
DESIGNATION
FIN. FLOOR, TYP.
UNDERSIDE OF DECK
OR BEAM ABOVE, TYP.
CONT. SEALANT
BOTH SIDES, TYP.
CONT. SEALANT
BOTH SIDES, TYP.
24 GA METAL STUDS
AT 16" O.C.
SLIP TRACK
3 5/8" (3)
A-3A1
FILL CAVITY WITH FIBER
GLASS ACOUSTICAL
INSULATION
GB-1
7/8" FURRING CHANNEL
AT 16" O.C. VERTICALLY
AND RESILIENT
ISOLATION CLIPS
STUD SIZE
GBI-1
GB-1
3 5/8" (3)
SYMBOL:
STUD SIZE
WALL TYPE
1A-6
SYMBOL:
STUD SIZE
WALL TYPE
STC 58
ACOUSTICAL
DESIGNATION
SYMBOL:
WALL TYPE
STC 63
GBI-1
GB-1
GBI-1
6" (6)
1 5/8"
FIN. FLOOR, TYP.
UNDERSIDE OF DECK
OR BEAM ABOVE, TYP.
CONT. SEALANT,
TYP.
SYMBOL:
CONT. SEALANT, TYP.
STUD SIZE
WALL TYPE
METAL STUD GB-1
ONE SIDE
SLIP TRACK
B SERIES PARTITIONB
1 5/8" (1)
2 1/2" (2)
3 5/8" (4)
6" (6)
B-6
GENERATOR SIDE
E SERIES EXTERIOR WALL ASSEMBLIESE
E7-01
7 5/8" GROUND FACE CMU, SEE
STRUCTURAL FOR REINFORCEMENT
EXTERIOR
7 5/8"
VERTICAL ORIENTED WATER
MANAGEMENT SYSTEM BY E.I.F.S
MANUFACTURER
2" XPS RIGID INSULATION
AB-2
BASE COAT
FINISH COAT, MATCH TEXTURE OF
EXISTING INSTALLATION
METAL OR WOOD STUD TO
MATCH EXISTING CONSTRUCTION
WALL THICKNESS
GB1-1 WHERE APPLICABLE
EXTERIORINTERIOR
6E-01
3" INSUL-8
1/2"
3/8" WATER MANAGEMENT
2"
PLYWOOD SHEATHING
TO MATCH EXISTING
THICKNESS
AB-2
LAP SIDING TO MATCH
EXISTING
METAL OR WOOD STUD TO
MATCH EXISTING CONSTRUCTION
WALL THICKNESS
GB1-1 WHERE APPLICABLE
EXTERIORINTERIOR
6E-02
INSUL-4
1/2"
3
FIN. FLOOR, TYP.
UNDERSIDE OF DECK
OR BEAM ABOVE, TYP.
SYMBOL:
WALL SIZE
WALL TYPE
PRIMARY WALL PARTITION
ASSEMBLY AS NOTED ON
FLOOR PLANS
W SERIES PARTITIONW
1 1/2" (2)
WP-2
7/16" OSB MECHANICAL
FASTENED TO PRIMARY WALL
AND CEILING
METAL STUD CEILING DESIGNED
TO SUPPORT 5 LBS / SF
GB-1
SAFETY PADS BY OWNER VENDOR;
COORDINATE LOCATION OF FASTENERS
AND VENDOR DRAWERS FOR PROPER
PRIMARY WALL, CEILING, AND OSB
SUBSTRATE PREPARATION
issue date
project #
phasesheet projectownerrevision dateaddress
BID SET10/31/2022 9:28:59 AM11-01-223
A1.2.1
09/15/2022ASSEMBLY TYPES22006.00
BID SET SPANISH PEAKSCONNECTIONS HEALTH SOLUTIONS120 19TH AVE. UNIT 1BOZEMAN, MONTANA 59718VERTICAL ASSEMBLIES
HORIZONTAL ASSEMBLIES
1. NO NEW HORIZONTAL ASSEMBLIES
2. EXISTING HORIZONTAL ROOF ASSEMBLIES TO MATCH EXISTING,
COORDINATE WITH STRUCTURAL DRAWINGS FOR BRACING OF EXISTING
ROOF WHERE ROOF TOP UNITS REQUIRE BRACING.